- 您現在的位置：買賣IC網 > PDF目錄11655 > HIP9011ABZ (Intersil)IC SENSOR ENGINE KNOCK 20-SOIC PDF資料下載
參數資料
| 型號： | HIP9011ABZ |
| 廠商： | Intersil |
| 文件頁數： | 2/11頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC SENSOR ENGINE KNOCK 20-SOIC |
| 標準包裝： | 380 |
| 類型： | 引擎敲擊信號處理器 |
| 輸入類型： | 邏輯 |
| 輸出類型： | 邏輯 |
| 接口： | SPI |
| 電流 - 電源： | 8mA |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 20-SOIC（0.295"，7.50mm 寬） |
| 供應商設備封裝： | 20-SOIC |
| 包裝： | 管件 |
10
FN4367.2
January 6, 2006
The Digital SPI Block diagram in Figure 5 shows the
programming flow of the chip. An eight bit word is received at
the SI port. Data is shifted in by the SCK clock when the chip
is enable by the CS pin. The word is decoded by the address
decoding circuit, and the information is directed to one of 5
registers. These registers control the following chip functions:
1. Band Pass Filter frequency.
2. Gain control or attenuation.
3. Integration time constant of the rectified BPF output.
4. Prescaler.
5. Test/Channel Select.
a) Test conditions of the part.
b) Channel select to one of two input amplifiers.
A crystal oscillator circuit is provided. The chip requires at
minimum a 4MHz crystal to be connected across OSCIN and
OSCOUT pins. An external 4MHz signal may also be
provided to the OSCIN Terminal Pin 9.
In the diagnostic mode, we can use the digital multiplexer to
output one of the following results through the SO pin (11):
1. Value of one of the five registers in the chip
2. Buffered value of the SI pin (12).
3. Value of an internal comparator used to rectify the analog
signal
A digital SPI filter is located in the SPI Block which provides
a pseudo noise immunity characteristic.
The digital SPI filter operation requires that the SCK be low
prior to the fall of CS, followed by 8 SCK pulses (low-high-
low transitions). With the SCK ending the pulse sequence in
a logic low condition, the transition of CS from a low to high
transition will cause the data-word in the SPI Buffer to be
loaded into the proper addressed programmable register.
During the Integration mode, INT/HOLD pin is high, any
single SPI byte that is entered will be acted upon if the
conditions of the digital SPI filter are met. The digital SPI
filter allows for only 8 bits per word to be accepted.
SP
IINT
E
RF
A
C
E
SCK
CS
ADDRESS DECODER
PRESCALER/SO TERMINAL STATUS
GAIN CONTROL
INTEGRATOR TIME CONSTANT
TEST/CHANNEL SELECT CONTROL
COMP OUT
SO
SI
D
IG
ITA
L
M
U
LT
IP
L
E
X
E
R
BANDPASS FILTER
FIGURE 5. PROGRAMMABLE REGISTERS AND STATE MACHINE
SI
TEST
HIP9011
相關PDF資料 |
PDF描述 |
|---|---|
| VE-JNV-IY-F1 | CONVERTER MOD DC/DC 5.8V 50W |
| D38999/24WJ29PN | CONN RCPT 29POS JAM NUT W/PINS |
| MC9S08AC128CLKE | MCU 128K FLASH 8K RAM 80-LQFP |
| D38999/24MF32SA | CONN RCPT 32POS JAM NUT W/SCKT |
| MCZ33784EF | IC SENSOR DBUS DSI 2.02 16-SOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HIP9011ABZT | 功能描述:接口 - 專用 W/ANNEAL KNOCK SENSOR TAPE RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59 |
| HIP9011ABZTR5133 | 制造商:Intersil Corporation 功能描述:PB-FREE VISTEON HIP9011ABZT W/BARCODE LABELS,PB DIE,ELECT SE - Tape and Reel 制造商:Intersil Corporation 功能描述:ITSHIP9011ABZTR5133 W/BARCODE LABELS,PB |
| HIP9011EVAL1Z | 功能描述:電源管理IC開發工具 HIP9011 EVAL BRD 1 ROHS CMPL RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
| HIP9020 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Programmable Quad Buffer with Pre and Post Scaler Dividers |
| HIP9020AB | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
發布緊急采購，3分鐘左右您將得到回復。