- 您現在的位置：買賣IC網 > PDF目錄371822 > HIP6501 (Intersil Corporation) Triple Linear Power Controller with ACPI Control Interface PDF資料下載
參數資料
| 型號： | HIP6501 |
| 廠商： | Intersil Corporation |
| 元件分類： | 基準電壓源/電流源 |
| 英文描述： | Triple Linear Power Controller with ACPI Control Interface |
| 中文描述： | 三線性電源控制器ACPI控制接口 |
| 文件頁數： | 9/14頁 |
| 文件大?。?/td> | 140K |
| 代理商： | HIP6501 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁當前第9頁第10頁第11頁第12頁第13頁第14頁
9
Soft-Start into Active States (S0, S1)
If both S3 and S5 are logic high at the time the 5VSB is
applied, the HIP6501A will assume an active state and keep
off the controlled external transistors until about 50ms after
the ATX’s 12V output (sensed at the 12V pin) exceeds the
set threshold (typically 10.8V). This timeout feature is
necessary in order to ensure the main ATX outputs are
stabilized. The timeout also assures smooth transitions from
sleep into active when sleep states are being supported.
During sleep to active state transitions from conditions
where the outputs are initially 0V (such as S4/S5 to S0
transition with EN3VDL = 1 and EN5VDL = 0, or simple
power-up sequence directly into active state), the 3V
DUAL
and 5V
DUAL
outputs go through a quasi soft-start by being
pulled high through the body diodes of the N-channel
MOSFETs connected between these outputs and the 3.3V
and 5V ATX outputs, respectively. Figure 10 shows this start-
up scenario.
5V
SB
is already present when the main ATX outputs are
turned on at time T0. Similarly, the soft-start capacitor has
already been charged up to 1.25V and the clamp is active,
awaiting for the 12V POR timer to expire. As a result of
3.3V
IN
and 5V
IN
ramping up, the 3.3V
DUAL
and 5V
DUAL
output capacitors charge up through the body diodes of Q3
and Q5, respectively (see Figure 3). At time T1, the 12V ATX
output exceeds the HIP6501A’s 12V under-voltage
threshold, and the internal 50ms (typical) timer is initiated. At
T2 the time-out initiates a soft-start, and the memory output
is ramped-up, reaching regulation limits at time T3.
Simultaneous with the memory voltage ramp-up, the DLA
pin is pulled high (to 12V), turning on Q3 and Q5, and
bringing the 3.3V
DUAL
and 5V
DUAL
outputs in regulation at
time T2. At time T4, when the soft-start voltage reaches
approximately 2.8V, the under-voltage monitoring circuits are
enabled and the soft-start capacitor is quickly discharged to
approximately 2.45V.
Requests to go into a sleep state during an active state soft-
start ramp-up result in a chip reset, followed by a new soft-
start sequence into the desired state.
Fault Protection
All the outputs are monitored against under-voltage events.
A severe over-current caused by a failed load on any of the
outputs, would, in turn, cause that specific output to
suddenly drop. If any of the output voltages drop below 69%
of their set value, such event is reported by having the
FAULT/MSEL pin pulled to 5V. Additionally, the 2.5/3.3V
memory regulator is internally current limited while in a sleep
state. Exceeding the maximum current rating of this output in
a sleep state can lead to output voltage drooping. If
excessive, this droop can ultimately trip the under-voltage
detector and send a FAULT signal to the computer system.
However, a FAULT condition will only set off the FAULT flag,
and it will not shut off or latch off any part of the circuit. If
shutdown or latch off of the circuit is desired, this can be
achieved by externally pulling or latching the SS pin low.
Pulling the SS pin low will also force the FAULT pin to go low.
Under-voltage sensing is disabled on all disabled outputs
and during soft-start ramp-up intervals. SS voltage reaching
the 2.8V threshold signals activation of the under-voltage
monitor.
Another condition that could set off the FAULT flag is chip
over-temperature. If the HIP6501A reaches an internal
temperature of 125
o
C (minimum), the FAULT flag is set
(FAULT/MSEL pulled high), but the chip continues to operate
until the temperature reaches 150
o
C (typical), when
unconditional latched shutdown of all outputs takes place.
The thermal latch can be reset only by cycling the 5V
SB
off,
and then on.
Output Voltages
The output voltages are internally set and do not require any
external components. Selection of the memory voltage is
done by means of an external resistor connected between
the FAULT/MSEL pin and ground. An internal 40
μ
A (typical)
current source creates a voltage drop across this resistor.
During every 5VSB trip above POR level, this voltage is
compared with an internal reference (200mV typically).
Based on this comparison, the output voltage is set at either
2.5V (R
SEL
= 1k
), or 3.3V (R
SEL
= 10k
). It is very
important that no capacitor is connected to the FAULT/MSEL
pin; the presence of a capacitive element at this pin can lead
to false memory voltage selection. See Figure 11 for details.
FIGURE 10. SOFT-START INTERVAL IN AN ACTIVE STATE
0V
0V
TIME
SOFT-START
(1V/DIV)
OUTPUT
VOLTAGES
(1V/DIV)
T1
T2
T0
INPUT VOLTAGES
(2V/DIV)
T4
T3
+5V
IN
+12V
IN
DLA PIN
(2V/DIV)
+5VSB
V
OUT2
(2.5V
MEM
)
V
OUT1
(3.3V
DUAL
)
V
OUT3
(5V
DUAL
)
+3.3V
IN
HIP6501A
相關PDF資料 |
PDF描述 |
|---|---|
| HIP6501A | Triple Linear Power Controller with ACPI Control Interface(帶ACPI控制接口的線性電源控制器) |
| HIP6501EVAL1 | Triple Linear Power Controller with ACPI Control Interface |
| HIP6501ACB | Triple Linear Power Controller with ACPI Control Interface |
| HIP6521 | PWM and Triple Linear Power Controller |
| HIP6521CB | PWM and Triple Linear Power Controller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HIP6501A | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Triple Linear Power Controller with ACPI Control Interface |
| HIP6501A_04 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Triple Linear Power Controller with ACPI Control Interface |
| HIP6501ACB | 功能描述:IC PWM TRIPLE POWER CTRLR 16SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 電源控制器，監視器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 應用:多相控制器 輸入電壓:- 電源電壓:9 V ~ 14 V 電流 - 電源:- 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:40-WFQFN 裸露焊盤 供應商設備封裝:40-TQFN-EP（5x5） 包裝:帶卷 (TR) |
| HIP6501ACB-T | 功能描述:IC PWM TRIPLE POWER CTRLR 16SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 電源控制器，監視器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 應用:多相控制器 輸入電壓:- 電源電壓:9 V ~ 14 V 電流 - 電源:- 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:40-WFQFN 裸露焊盤 供應商設備封裝:40-TQFN-EP（5x5） 包裝:帶卷 (TR) |
| HIP6501ACBZ | 功能描述:PMIC 解決方案 COMPANION CHIP TO HI6020/21 RoHS:否 制造商:Texas Instruments 安裝風格:SMD/SMT 封裝 / 箱體:QFN-24 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。