- 您現在的位置：買賣IC網 > PDF目錄371822 > HIP6500CB (INTERSIL CORP) Multiple Linear Power Controller with ACPI Control Interface PDF資料下載
參數資料
| 型號： | HIP6500CB |
| 廠商： | INTERSIL CORP |
| 元件分類： | 電源管理 |
| 英文描述： | Multiple Linear Power Controller with ACPI Control Interface |
| 中文描述： | 9-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO20 |
| 封裝： | PLASTIC, MS-013-AC, SOIC-20 |
| 文件頁數： | 13/15頁 |
| 文件大小： | 155K |
| 代理商： | HIP6500CB |
13
the supplied outputs. At the transition between active and
sleep states, this phenomena could result in the 5VSB
voltage dropping below the POR level (typically 4.1V) and
temporarily disabling the HIP6500. The solution to a
potential problem such as this is using larger input
capacitors with a lower total combined ESR.
Transistor Selection/Considerations
The HIP6500 usually requires one P-Channel (or bipolar
PNP), two N-Channel MOSFETs and two bipolar NPN
transistors.
One important criteria for selection of transistors for all the
linear regulators/switching elements is package selection for
efficient removal of heat. The power dissipated in a linear
regulator/switching element is
Select a package and heatsink that maintains the junction
temperature below the rating with the maximum expected
ambient temperature.
Q1
The active element on the 2.5V/3.3V
MEM
output has
different requirements for each of the two voltage settings. In
2.5V systems utilizing RDRAM (or voltage-compatible)
memory, Q1 has to be a bipolar NPN capable of conducting
up to 7.5A and exhibit a current gain (h
fe
) of minimum 40 at
this current and 0.7V V
CE
; in such systems the 2.5V output
is actively regulated while in active state. In 3.3V systems
(SDRAM or compatible) Q1 has to be an N-Channel
MOSFET; in such systems the MOSFET is switched on
during active state (S0, S1). The main criteria for the
selection of this transistor is output voltage budgeting. The
maximum r
DS(ON)
allowed at highest junction temperature
can be expressed with the following equation:
V
OUTmax
, where
V
INmin
- minimum input voltage
V
OUTmin
- minimum output voltage allowed
I
OUTmax
- maximum output current
The gate bias available for this MOSFET is of the order of 8V.
Q5
If a P-Channel MOSFET is used to switch the 5VSB output
of the ATX supply into the 5V
DUAL
output during S3 and S5
states (as dictated by EN5VDL status), then, similar to the
situation where Q1 is a MOSFET, the selection criteria of this
device is also proper voltage budgeting. The maximum
r
DS(ON)
, however, has to be achieved with only 4.5V of V
GS
,
so a logic level MOSFET needs to be selected. If a PNP
device is chosen to perform this function, it has to have a low
saturation voltage while providing the maximum sleep
current and have a current gain sufficiently high to be
saturated using the minimum drive current (typically 20mA).
Q3,4
The two N-Channel MOSFETs are used to switch the 3.3V
and 5V inputs provided by the ATX supply into the
3.3VDUAL and 5VDUAL outputs, respectively, while in active
(S0, S1) state. Similar r
DS(ON)
criteria apply in these cases
as well. Unlike the PMOS, however, these NMOS transistors
get the benefit of an increased V
GS
drive (approximately 8V
and 7V, respectively).
Q2
The NPN transistor used as sleep state pass element (Q2)
on the 3.3V
DUAL
output has to have a minimum current gain
of 100 at 1.5V V
CE
and 500mA I
CE
throughout the in-circuit
operating temperature range.
P
LINEAR
I
O
V
IN
V
OUT
–
(
)
×
=
r
DS ON
)
max
V
–
--------------------------------------------------
=
HIP6500
相關PDF資料 |
PDF描述 |
|---|---|
| HIP6500EVAL1 | Multiple Linear Power Controller with ACPI Control Interface |
| HIP6501 | Triple Linear Power Controller with ACPI Control Interface |
| HIP6501A | Triple Linear Power Controller with ACPI Control Interface(帶ACPI控制接口的線性電源控制器) |
| HIP6501EVAL1 | Triple Linear Power Controller with ACPI Control Interface |
| HIP6501ACB | Triple Linear Power Controller with ACPI Control Interface |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HIP6500CB-TS2490 | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| HIP6500EVAL1 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Multiple Linear Power Controller with ACPI Control Interface |
| HIP6501 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Triple Linear Power Controller with ACPI Control Interface |
| HIP6501A | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Triple Linear Power Controller with ACPI Control Interface |
| HIP6501A_04 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Triple Linear Power Controller with ACPI Control Interface |
發布緊急采購，3分鐘左右您將得到回復。