- 您現在的位置：買賣IC網 > PDF目錄371820 > HIP1011DCA-T (INTERSIL CORP) Dual PCI Hot Plug Controller PDF資料下載
參數資料
| 型號： | HIP1011DCA-T |
| 廠商： | INTERSIL CORP |
| 元件分類： | 模擬信號調理 |
| 英文描述： | Dual PCI Hot Plug Controller |
| 中文描述： | SPECIALTY ANALOG CIRCUIT, PDSO28 |
| 封裝： | 0.150 INCH, PLASTIC, SSOP-28 |
| 文件頁數： | 1/15頁 |
| 文件大小： | 139K |
| 代理商： | HIP1011DCA-T |
1
File Number
4725.1
HIP1011D
Dual PCI Hot Plug Controller
The HIP1011D is the first IC available for independent
control of two PCI Hot Plug slots. The HIP1011D has all the
features and functionality of two single PCI Hot Plug slot
controllers such as the HIP1011A but in the same foot print
area.
The HIP1011D is designed to be physically placed in close
proximity to two adjacent PCI slots servicing each
independently but reducing layout complexity and placement
costs in assembly. It creates two independent power control
solutions with discrete power MOSFETs and a few passive
components. The four supplies +5V, +3.3V, +12V, and -12V
for each slot are independently controlled. There are four
integrated current sensing switches for the +12V and -12V
and for the +5V and +3.3V supplies overcurrent protection is
provided by sensing the voltage across external current-
sense resistors. In addition, on-chip references are used to
monitor the +5V, +3.3V and +12V outputs for undervoltage
conditions. The two PWRON inputs control the state of the
switches, one each for slot A and slot B outputs. During an
overcurrent condition on any output, or an undervoltage
condition on the +5V, +3.3V or +12V outputs, a LOW (0V) is
asserted on the associated FLTN output and all associated
switches are latched-off. The outputs servicing the adjacent
slot are unaffected.
The time to FLTN signal going LOW and MOSFET latch off
is user determined by a single capacitor from each FLTN pin
to ground. This added feature enables the HIP1011D to
ignore system noise transients. The FLTN latch is cleared
when the PWRON input is toggled low again. During initial
power-up of the main VCC supply (+12V), the PWRON input
is inhibited from turning on the switches, and the latch is held
in the Reset state until the VCC input is greater than 10V.
User programmability of the overcurrent threshold and turn-
on slew rate is provided. A resistor connected to the OCSET
pin programs the overcurrent threshold for both slots.
Capacitors connected to the gate pins set the turn-on rate.
Features
Independent Power Control of 2 PCI Slots
Turn-Off Delay Time Adjustability
Internal MOSFET Switches for +12V and -12V Outputs
μ
P Interface for On/Off Control and Fault Reporting
Adjustable Overcurrent Protection for All Eight Supplies
Provides Fault Isolation
Adjustable Turn-On Slew Rate
Minimum Parts Count Solution
No Charge Pump
100ns Response Time to Over Current
Applications
PCI Hot-Plug
Pinout
HIP1011D
(SSOP)
TOP VIEW
Ordering Information
PART NUMBER
TEMP.RANGE
(
o
C)
PACKAGE
PKG.
NO.
HIP1011DCA
0 to 70
28 Ld SSOP
M28.15
HIP1011DCA-T
0 to 70
Tape and Reel
28
27
26
25
24
23
22
21
20
19
18
17
16
15
1
2
3
4
5
6
7
8
9
10
11
12
13
14
M12VO_1
M12VG_1
12VIN_1
M12VO_2
M12VG_2
12VG_2
12VO_2
M12VIN_2
12VO_1
12VIN_2
12VG_1
M12VIN_1
3VISEN_2
3VS_2
3V5VG_2
PWRON_2
5VISEN_2
FLTN_2
VSS
OCSET
PWRON_1
FLTN_1
5VS_1
5VISEN_1
3VISEN_1
3VS_1
3V5VG_1
5VS_2
Data Sheet
November 1999
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 321-724-7143
|
Copyright
Intersil Corporation 1999
相關PDF資料 |
PDF描述 |
|---|---|
| HIP1011E | Dual Slot PCI Hot Plug Controller |
| HIP1011 | PCI Hot Plug Controller |
| HIP1011CB | PCI Hot Plug Controller |
| HIP1011CB-T | PCI Hot Plug Controller |
| HIP1013CB-T | Low Cost Dual Power Distribution Controller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HIP1011DCAZA | 功能描述:熱插拔功率分布 W/ANNEAL DL VER OF HIP1011 2 8LD SSOP RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| HIP1011DCAZA-T | 功能描述:熱插拔功率分布 W/ANNEAL DL PCI HOT PLUG PWR CNTRLR RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| HIP1011DEVAL1 | 功能描述:電源管理IC開發工具 DL SLOT PCI HOT PLUG EVALUATION BRD RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
| HIP1011E | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Dual Slot PCI Hot Plug Controller |
| HIP1011ECA | 功能描述:IC CTRLR HOTPLUG DUAL 28-SSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:100 系列:- 類型:熱插拔開關 應用:通用 內部開關:是 電流限制:可調 電源電壓:9 V ~ 13.2 V 工作溫度:-40°C ~ 150°C 安裝類型:表面貼裝 封裝/外殼:10-WFDFN 裸露焊盤 供應商設備封裝:10-TDFN-EP（3x3） 包裝:管件 |
發布緊急采購，3分鐘左右您將得到回復。