- 您現在的位置：買賣IC網 > PDF目錄371815 > HI5767EVAL1 (Intersil Corporation) 10-Bit, 20/40/60 MSPS A/D Converter with Internal Voltage Reference PDF資料下載
參數資料
| 型號： | HI5767EVAL1 |
| 廠商： | Intersil Corporation |
| 英文描述： | 10-Bit, 20/40/60 MSPS A/D Converter with Internal Voltage Reference |
| 中文描述： | 10位，20/40/60 MSPS的A / D轉換器內部電壓基準 |
| 文件頁數： | 11/13頁 |
| 文件大?。?/td> | 133K |
| 代理商： | HI5767EVAL1 |
11
in a gain-of-two configuration. An external, user-supplied,
0.1
μ
F capacitor connected from the V
REFOUT
output pin to
analog ground is used to set the dominant pole and to
maintain the stability of the operational amplifier.
Reference Voltage Input, V
REFIN
The HI5767 is designed to accept a +2.5V reference voltage
source at the V
REFIN
input pin. Typical operation of the
converter requires V
REFIN
to be set at +2.5V. The HI5767 is
tested with V
REFIN
connected to V
REFOUT
yielding a fully
differential analog input voltage range of
±
0.5V.
The user does have the option of supplying an external
+2.5V reference voltage. As a result of the high input
impedance presented at the V
REFIN
input pin, 2.5k
typically, the external reference voltage being used is only
required to source 1mA of reference input current. In the
situation where an external reference voltage will be used
an external 0.1
μ
F capacitor
must
be connected from the
V
REFOUT
output pin to analog ground in order to maintain
the stability of the internal operational amplifier.
In order to minimize overall converter noise it is
recommended that adequate high frequency decoupling be
provided at the reference voltage input pin, V
REFIN
.
Analog Input, Differential Connection
The analog input to the HI5767 is a differential input that can
be configured in various ways depending on the signal
source and the required level of performance. A fully
differential connection (Figure 17 and Figure 18) will deliver
the best performance from the converter.
Since the HI5767 is powered by a single +5V analog supply,
the analog input is limited to be between ground and +5V.
For the differential input connection this implies the analog
input common mode voltage can range from 0.25V to 4.75V.
The performance of the ADC does not change significantly
with the value of the analog input common mode voltage.
A DC voltage source, V
DC
, equal to 3.2V (typical), is made
available to the user to help simplify circuit design when using
an AC coupled differential input. This low output impedance
voltage source is not designed to be a reference but makes an
excellent DC bias source and stays well within the analog
input common mode voltage range over temperature.
For the AC coupled differential input (Figure 17) and with
V
REFIN
connected to V
REFOUT
, full scale is achieved when
the V
IN
and -V
IN
input signals are 0.5V
P-P
, with -V
IN
being
180 degrees out of phase with V
IN
. The converter will be at
positive full scale when the V
IN
+ input is at V
DC
+ 0.25V and
the V
IN
- input is at V
DC
- 0.25V (V
IN
+ - V
IN
- = +0.5V).
Conversely, the converter will be at negative full scale when
the V
IN
+ input is equal to V
DC
- 0.25V and V
IN
- is at
V
DC
+ 0.25V (V
IN
+ - V
IN
- = -0.5V).
The analog input can be DC coupled (Figure 18) as long as
the inputs are within the analog input common mode voltage
range (0.25V
≤
VDC
≤
4.75V).
The resistors, R, in Figure 18 are not absolutely necessary
but may be used as load setting resistors. A capacitor, C,
connected from V
IN
+ to V
IN
- will help filter any high
frequency noise on the inputs, also improving performance.
Values around 20pF are sufficient and can be used on AC
coupled inputs as well. Note, however, that the value of
capacitor C chosen must take into account the highest
frequency component of the analog input signal.
Analog Input, Single-Ended Connection
The configuration shown in Figure 19 may be used with a
single ended AC coupled input.
Again, with V
REFIN
connected to V
REFOUT
, if V
IN
is a 1V
P-P
sinewave, then V
IN
+ is a 1.0V
P-P
sinewave riding on a positive
voltage equal to VDC. The converter will be at positive full scale
when V
IN
+ is at VDC + 0.5V (V
IN
+ - V
IN
- = +0.5V) and will be at
negativefullscalewhenV
IN
+isequaltoVDC - 0.5V (V
IN
+-V
IN
-
= -0.5V). Sufficient headroom must be provided such that the
inputvoltagenevergoesabove+5VorbelowAGND.Inthiscase,
VDC could range between 0.5V and 4.5V without a significant
change in ADC performance. The simplest way to produce VDC
is to use the DC bias source, V
DC
, output of the HI5767.
The single ended analog input can be DC coupled
(Figure 20) as long as the input is within the analog input
common mode voltage range.
V
IN
+
V
DC
V
IN
-
HI5767
V
IN
-V
IN
R
R
FIGURE 16. AC COUPLED DIFFERENTIAL INPUT
V
IN
+
V
DC
V
IN
-
HI5767
V
IN
-
V
IN
R
R
C
VDC
VDC
FIGURE 17. DC COUPLED DIFFERENTIAL INPUT
V
IN
+
V
IN
-
HI5767
V
IN
VDC
R
FIGURE 18. AC COUPLED SINGLE ENDED INPUT
HI5767
相關PDF資料 |
PDF描述 |
|---|---|
| HI5780JCQ-T | Video DAC without Color Palette |
| HI5801JCM | ADVANCE INFORMATION |
| HI5801 | ADVANCE INFORMATION |
| HI5801AIJ | ADVANCE INFORMATION |
| HI5801BIJ | ADVANCE INFORMATION |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HI5767EVAL2 | 功能描述:數據轉換 IC 開發工具 HI5767 HI FREQUENCY EVALUATION PLATFORM RoHS:否 制造商:Texas Instruments 產品:Demonstration Kits 類型:ADC 工具用于評估:ADS130E08 接口類型:SPI 工作電源電壓:- 6 V to + 6 V |
| HI5780 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:10-Bit, 80 MSPS, High Speed, Low Power D/A Converter |
| HI5780-EV | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:10-Bit, 80 MSPS, High Speed, Low Power D/A Converter |
| HI5780JCQ | 制造商:Rochester Electronics LLC 功能描述:32 PQFP COMTEMP VIDEO D/A 10BIT 80MHZ - Bulk 制造商:Harris Corporation 功能描述: |
| HI5780JCQ-T | 制造商:Rochester Electronics LLC 功能描述:HI5780JCQ IN TAPE & REEL - Bulk |
發布緊急采購，3分鐘左右您將得到回復。