參數資料
型號： HFCT-5952TG
英文描述： FIBER OPTIC TRANSCEIVER
中文描述： 光纖收發器
文件頁數： 4/10頁
文件大?。?/td> 224K
代理商： HFCT-5952TG
3
Functional Description
Receiver Section
Design
The receiver section contains an
InGaAs/InP photo detector and a
preamplifier within the receptacle,
coupled to a postamp/decision
circuit on a separate circuit board.
The postamplifier is ac coupled to
the preamplifier as illustrated in
Figure 1. The coupling capacitor
is large enough to pass the
SONET/SDH test pattern at
155 MBd without significant
distortion or performance penalty.
If a lower signal rate, or a code
which has significantly more low
frequency content is used,
sensitivity, jitter and pulse
distortion could be degraded.
Figure 1 also shows a filter
network which limits the
bandwidth of the preamp output
signal. The filter is designed to
bandlimit the preamp output
noise and thus improve the
receiver sensitivity.
These components will also
reduce the sensitivity of the
receiver as the signal bit rate is
increased above 155 MBd.
Noise Immunity
The receiver includes internal
circuit components to filter
power supply noise. Under some
conditions of EMI and power
supply noise, external power
supply filtering may be necessary.
If receiver sensitivity is found to
be degraded by power supply
noise, the filter network illustrated
in Figure 2 may be used to improve
performance. The values of the
filter components are general
recommendations and may be
changed to suit a particular
system environment. Shielded
inductors are recommended.
Terminating the Outputs
The PECL Data outputs of the
receiver may be terminated with
the standard Thevenin-equivalent
50 ohm to VCC - 2 V termination.
Other standard PECL terminating
techniques may be used.
The two outputs of the receiver
should be terminated with
identical load circuits to avoid
unnecessarily large ac current in
VCC. If the outputs are loaded
identically the ac current is largely
nulled. The Signal Detect output
of the receiver is PECL logic and
must be loaded if it is to be used.
The Signal Detect circuit is much
slower than the data path, so the
ac noise generated by an
asymmetrical load is negligible.
Power consumption may be
reduced by using a higher than
normal load impedance for the
Signal Detect output.
Transmission line effects are not
generally a problem as the
switching rate is slow.
The Signal Detect Circuit
The Signal Detect circuit works by
sensing the peak level of the
received signal and comparing
this level to a reference.
Figure 1 - Receiver Block Diagram
Figure 2 -
p Filter Network for Noise Filtering
V
CC
100 nF
3.3 H
100 nF
10 F
FILTERED V
CC to DATA LINK
+
RECEIVER
RECEPTACLE
TRANS-
IMPEDANCE
PRE-
AMPLIFIER
FILTER
GND
LIMITING
AMPLIFIER
PECL
OUTPUT
BUFFER
PECL
OUTPUT
BUFFER
DATA OUT
SIGNAL
DETECT
CIRCUIT
SD
DATA OUT
相關PDF資料
PDF描述
HFCT-5952TL Optoelectronic
HFCT-5953ATG Optoelectronic
HFCT-5953ATL Optoelectronic
HFCT-5953TG Optoelectronic
HFCT-5953TL Optoelectronic
相關代理商/技術參數
參數描述
HFCT-5952TGZ 功能描述:光纖發射器、接收器、收發器 OC12 IR 2x10 LC No N ose Sh RoHS RoHS:否 制造商:Omron Electronics 產品:Transmitters 數據速率:3.5 Gbps 波長:850 nm 最大工作溫度: 最小工作溫度: 封裝 / 箱體: 封裝:
HFCT-5952TL 功能描述:光纖發射器、接收器、收發器 OC12 IR 2x10 SFF LC RoHS:否 制造商:Omron Electronics 產品:Transmitters 數據速率:3.5 Gbps 波長:850 nm 最大工作溫度: 最小工作溫度: 封裝 / 箱體: 封裝:
HFCT-5952TLZ 功能描述:光纖發射器、接收器、收發器 OC12 IR 2x10 SFF LC RoHS RoHS:否 制造商:Omron Electronics 產品:Transmitters 數據速率:3.5 Gbps 波長:850 nm 最大工作溫度: 最小工作溫度: 封裝 / 箱體: 封裝:
HFCT-5953ATG 功能描述:光纖發射器、接收器、收發器 OC12 IR2X5 LC EXTTMP NO NOSE SHLD RoHS:否 制造商:Omron Electronics 產品:Transmitters 數據速率:3.5 Gbps 波長:850 nm 最大工作溫度: 最小工作溫度: 封裝 / 箱體: 封裝:
HFCT-5953ATGZ 功能描述:光纖發射器、接收器、收發器 OC12 IR2X5 LC EXTP N O NOSE SH RoHS RoHS:否 制造商:Omron Electronics 產品:Transmitters 數據速率:3.5 Gbps 波長:850 nm 最大工作溫度: 最小工作溫度: 封裝 / 箱體: 封裝:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*