- 您現在的位置：買賣IC網 > PDF目錄296100 > HFCT-5208M 622 Mbit/s SMF (15km) 1x9 Transceiver for SONET/SDH. ATM (OC12): Metalized housing PDF資料下載
參數資料
| 型號： | HFCT-5208M |
| 英文描述： | 622 Mbit/s SMF (15km) 1x9 Transceiver for SONET/SDH. ATM (OC12): Metalized housing |
| 中文描述： | 622 Mbit / s的單模光纖（15公里）1x9收發器用于SONET / SDH的。自動柜員機（OC12）：金屬化住房 |
| 文件頁數： | 15/20頁 |
| 文件大小： | 503K |
| 代理商： | HFCT-5208M |
4
Figure 4. Recommended Circuit Schematic for dc Coupling (at +5 V) between Optical
Transceiver and Physical Layer IC
MOUNTING POST
NO INTERNAL CONNECTION
HFBR/HFCT-5208M
TOP VIEW
V
EER
RD
SD
V
CCR
V
CCT
TD
V
EET
1
234
567
89
C2
L1
L2
R2
R3
R1
R4
C5
C3
C4
R9
R10
V
CC FILTER
AT V
CC PINS
TRANSCEIVER
R5
R7
R6
R8
C6
RD
SD
V
CC
TD
TERMINATION
AT PHY
DEVICE
INPUTS
NOTES:
THE SPLIT-LOAD TERMINATIONS FOR PECL SIGNALS NEED TO BE LOCATED AT THE INPUT
OF DEVICES RECEIVING THOSE PECL SIGNALS. RECOMMEND MULTI-LAYER PRINTED
CIRCUIT BOARD WITH 50 OHM MICROSTRIP OR STRIPLINE SIGNAL PATHS BE USED.
R1 = R4 = R6 = R8 = R10 = 130 OHMS.
R2 = R3 = R5 = R7 = R9 = 82 OHMS.
C1 = C2 = C3 = C5 = C6 = 0.1 F.
C4 = C7 = 10 F.
L1 = L2 = 1 H COIL OR FERRITE INDUCTOR (see text comments).
TERMINATION
AT TRANSCEIVER
INPUTS
Rx
Tx
V
CC
V
CC
C1
C7
MOUNTING POST
NO INTERNAL CONNECTION
Maintain a solid, low inductance
ground plane for returning signal
currents to the power supply.
Multilayer plane printed circuit
board is best for distribution of
VCC, returning ground currents,
forming transmission lines and
shielding. Also, it is important to
suppress noise from influencing
the fiber-optic transceiver per-
formance, especially the receiver
circuit. Proper power supply
filtering of VCC for this transceiver
is accomplished by using the
recommended separate filter
circuits shown in Figure 4. These
filter circuits suppress VCC noise
of 100 mV peak-to-peak or less
over a broad frequency range.
This prevents receiver sensitivity
degradation . It is recommended
that surface-mount components
be used. Use tantalum capacitors
for the 10 F capacitors and
monolithic, ceramic bypass
capacitors for the 0.1 F
capacitors. Also, it is
recommended that a surface-
mount coil inductor of 1 H be
used. Ferrite beads can be used to
replace the coil inductors
when using quieter VCC supplies,
but a coil inductor is recom-
mended over a ferrite bead to
provide low-frequency noise
filtering as well. Coils with a low,
series dc resistance (<0.7 ohms)
and high, self-resonating
frequency are recommended. All
power supply components need to
be placed physically next to the
VCC pins of the receiver and
transmitter. Use a good, uniform
ground plane with a minimum
number of holes to provide a low-
inductance ground current return
path for the signal and power
supply currents.
Although the front mounting posts
make contact with the metallized
housing, these posts should not be
relied upon to provide adequate
electrical connection to the plated
housing. It is recommended to
either connect these front posts to
chassis ground or allow them to
remain unconnected. These front
posts should not be connected to
signal ground.
Figure 5 shows the recommended
board layout pattern.
In addition to these recommenda-
tions, Agilent’s Application
Engineering staff is available for
consulting on best layout practices
with various vendors’ serializer/
deserializer, clock recovery/
generation integrated circuits.
相關PDF資料 |
PDF描述 |
|---|---|
| HFCT-5215D | Conversion adapters; HRS No: 311-0008-0 40; Connector Type: Adapter; Impedance (ohm): 50; Mating/Unmating Cycles: 5000; Contact Mating Area Plating: Silver; Operating Temperature Range (degrees C): -55 to 85; General Description: BNC-Plug/M-Jack Conversion adapter |
| HFCT-53D3EM | 1 x 9 5V Fiber Optic Transceiver for Fibre Channel/Storage - Extended Shield. Metalized Housing |
| HFCT-53D3FM | 1 x 9 5V Fiber Optic Transceiver for Fibre Channel/Storage - Flush Shield. Metalized Housing |
| HFCT-53D5EM | 1 x 9 Fiber Optic Transceivers for Gigabit Ethernet |
| HFCT53D3 | FIBER OPTIC TRANSCEIVER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HFCT-5208MZ | 功能描述:光纖發射器、接收器、收發器 1x9 622Mbps IR ATM M tl Tx RoHS RoHS:否 制造商:Omron Electronics 產品:Transmitters 數據速率:3.5 Gbps 波長:850 nm 最大工作溫度: 最小工作溫度: 封裝 / 箱體: 封裝: |
| HFCT-5208XX | 制造商:AGILENT 制造商全稱:AGILENT 功能描述:Agilent HFBR/HFCT-5208M 1 x 9 Fiber Optic Transceivers for 622 Mb/s ATM/SONET/SDH Applications |
| HFCT-5215B | 制造商:AGILENT 制造商全稱:AGILENT 功能描述:Agilent HFCT-5215B/D 155 Mb/s Single Mode Laser Transceiver for ATM, SONET OC-3/SDH STM-1 (L1.1) |
| HFCT-5215D | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:155 Mb/s Single Mode Laser Transceiver for ATM. SONET OC-3/SDH STM-1 (L1.1) |
| HFCT-5218EM | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:622 Mbit/s SMF (40km) 1x9 Transceiver for SONET/SDH. ATM (OC-12): Ext. shield. metal housing |
發布緊急采購，3分鐘左右您將得到回復。