- 您現在的位置：買賣IC網 > PDF目錄361282 > HFBR-RUS500 Plastic Fiber Cable - Standard Attenuation. Unconnectored. Simplex Cable. 500 Meters PDF資料下載
參數資料
| 型號： | HFBR-RUS500 |
| 英文描述： | Plastic Fiber Cable - Standard Attenuation. Unconnectored. Simplex Cable. 500 Meters |
| 中文描述： | 塑料光纖電纜-標準衰減。 Unconnectored。單純電纜。 500米 |
| 文件頁數： | 6/11頁 |
| 文件大小： | 267K |
| 代理商： | HFBR-RUS500 |
6
Step 3
Any excess fiber protruding from
the connector end may be cut off;
however, the trimmed fiber
should extend at least 1.5 mm
(0.06 in) from the connector end.
Insert the connector fully into the
polishing fixture with the trimmed
fiber protruding from the bottom
of the fixture. This plastic polish-
ing fixture can be used to polish
two simplex connectors or simplex
latching connectors simultane-
ously, or one duplex connector.
Note:
The four dots on the
bottom of the polishing fixture
are wear indicators. Replace
the polishing fixture when any
dot is no longer visible.
Typically, the polishing fixture
can be used 10 times; 10 duplex
connectors or 20 simplex
connectors, two at a time.
Place the 600 grit abrasive paper
on a flat smooth surface, pressing
down on the connector, polish the
fiber and the connector using a
figure eight pattern of strokes
until the connector is flush with
the bottom of the polishing
fixture. Wipe the connector and
fixture with a clean cloth or
tissue.
Step 4
Place the flush connector and
polishing fixture on the dull side
of the 3
μ
m pink lapping film and
continue to polish the fiber and
connector for approximately 25
strokes. The fiber end should be
flat, smooth and clean.
This cable is now ready for use.
Note:
Use of the pink lapping
film fine polishing step results
in approximately 2 dB
improvement in coupling
performance of either a
transmitter-receiver link or a
bulkhead/splice over a 600 grit
polish alone. This fine polish is
comparable to the Agilent
factory polish. The fine
polishing step may be omitted
where an extra 2 dB of optical
power is not essential, as with
short link lengths. Proper
polishing of the tip of the fiber/
connector face results in a tip
diameter between 2.5 mm
(0.098 in.) minimum and 3.2
mm (0.126 in.) maximum..
HFBR-4593 Polishing Kit
相關PDF資料 |
PDF描述 |
|---|---|
| HFBR-0527H | Evaluation Kit for HFBR-1527 & HFBR-2526 125MBd Data Comm HCS Fiber for up to 100 meters |
| HFBR-0527P | Evaluation Kit for HFBR-1527 & HFBR-2526 125MBd Data Comm with POF for up to 25 meters |
| HFBR-0537 | Eval Kit for proprietary data com apps at data rates up to 32 MBd with AN 1121 figs. 3 & 5 |
| HFBR-1521 | 5 MBd 600nm High Performance Link Transmitter in Horizontal Package |
| HFBR-1523 | 40 kBd 600nm Low Current/Extended Distance Link Transmitter in Horizontal Package |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HFBR-RUS500Z | 功能描述:光纖線纜 BLK PLAST CABLE SMPL X 500 MTRSRoHS RoHS:否 制造商:Avago Technologies 類型:Plastic Optical Fiber (POF) 纖維類型: 外殼顏色:Black 長度:500 meters 外殼材料:Polyethylene |
| HFBR-RWS002 | 功能描述:光纖發射器、接收器、收發器 2 MTR PLAST CABLE AS Y SMPLX SMA RoHS:否 制造商:Omron Electronics 產品:Transmitters 數據速率:3.5 Gbps 波長:850 nm 最大工作溫度: 最小工作溫度: 封裝 / 箱體: 封裝: |
| HFBR-RWS002Z | 功能描述:光纖發射器、接收器、收發器 2MTR PLAST CABLE ASY SMPLX SMARoHS RoHS:否 制造商:Omron Electronics 產品:Transmitters 數據速率:3.5 Gbps 波長:850 nm 最大工作溫度: 最小工作溫度: 封裝 / 箱體: 封裝: |
| HFC | 制造商:MA-COM 制造商全稱:M/A-COM Technology Solutions, Inc. 功能描述:COMMERCIAL/INDUSTRIAL |
| HFC 2212-12 | 制造商:TOM PARKER 功能描述:INSERT HOSE BARB 3/4" |
發布緊急采購，3分鐘左右您將得到回復。