- 您現在的位置：買賣IC網 > PDF目錄370574 > HFBR-4532 Crimpless Connectors for Plastic Optical Fiber and Versatile Link(應用于塑料光纖和通用鏈接的無壓接連接器) PDF資料下載
參數資料
| 型號： | HFBR-4532 |
| 英文描述： | Crimpless Connectors for Plastic Optical Fiber and Versatile Link(應用于塑料光纖和通用鏈接的無壓接連接器) |
| 中文描述： | Crimpless連接器塑料光纖和通用連接（應用于塑料光纖和通用鏈接的無壓接連接器） |
| 文件頁數： | 2/6頁 |
| 文件大?。?/td> | 186K |
| 代理商： | HFBR-4532 |
2
Termination Guide
Step-by-Step Plastic Cable
Connectoring Instructions
The following step-by-step guide
describes how to terminate plastic
fiber optic cable. It is ideal for
both field and factory installa-
tions. Connectors can be easily
installed on cable ends with
standard tools such as wire
strippers and cutters.
Finishing the cable is accom-
plished with the Agilent
HFBR-4593 Polishing Kit,
consisting of a polishing fixture,
600 grid abrasive paper and 3
μ
m
pink lapping film (3M Company,
OC3-14). The connector can be
used immediately after polishing.
The following materials are
needed for plastic fiber
termination:
1. Plastic optical fiber cable
(Example: HFBR-RUD500)
2. Wire cutters or scissors
3. 16 gauge wire stripper
(Example: Ideal Stripmaster
type 45-092)
4. HFBR-4593 polishing kit
(optional)
5. Crimpless connectors
Step 1: Stripping the Fiber
The zip cord structure of the
duplex cable permits easy
separation of the channels. The
channels should be separated a
minimum of 100 mm (4 in) to a
maximum of 150 mm (6 in) back
from the ends to permit connec-
toring, polishing and cable end
flexibility.
After cutting the cable to the
desired length, strip off
approximately 7 mm (0.3 in) of
the outer jacket with the 16
gauge wire strippers.
When using the duplex connector
arrangement, the separated
duplex cable should be stripped
to roughly equal lengths on each
cable end.
For the non-latching version
(HFBR-4531), the same
connector is used for simplex and
duplex arrangement. No crimping
is necessary. The top half of the
connector will snap into the
ferrule half to secure the fiber.
Step 2: Putting on the
Connector
Place the connector on each end
of the fiber, and slide the
connector down until the fiber
jacket stops it. The fiber should
protrude
no less
than 1.5 mm
(0.06 in) from the end of the
connector.
To install
simplex
connectors flip
the top half of the connector over
and snap it into the ferrule half
(with your fingers). When the top
half latches inside the body of the
ferrule half, proper connector-to-
cable attachment is achieved.
For
duplex
connector installation
place one connector on top of the
other, so that the top half of each
connector is over the ferrule half
of the opposite connector.
Manually press connectors
together in the center of the
arrangement. Then latch by
pressing on the sides of each
connector. As with the simplex
version, connectors are secured
when top halves latch into the
ferrule halves.
Step 3: Trimming and
Polishing
Any fiber in excess of 1.5 mm
(0.06 in) protruding from the
connector end should be cut off
with wire cutters or scissors.
Insert the connector fully into the
polishing fixture with the
trimmed fiber protruding from
the bottom of the fixture. This
plastic polishing fixture can be
used to polish two simplex
connectors simultaneously or one
duplex connector.
相關PDF資料 |
PDF描述 |
|---|---|
| HFBR-4663 | Single Chip 10BASE-FL Transceiver(單芯片10BASE-FL收發器) |
| HFBR-5103 | 1300 nm 2000 m，F(xiàn)DDI, 100 Mbps ATM, and Fast Ethernet Transceivers in Low Cost 1x9 Package Style(1300 nm 2000 m，F(xiàn)DDI, 100 Mbps ATM, 快速以太網收發器（低價格 1x9 封裝類型）) |
| HFBR-5103T | 1300 nm 2000 m，F(xiàn)DDI, 100 Mbps ATM, and Fast Ethernet Transceivers in Low Cost 1x9 Package Style(1300 nm 2000 m，F(xiàn)DDI, 100 Mbps ATM, 快速以太網收發器（低價格 1x9 封裝類型）) |
| HFBR-5104T | 800 nm 500 m，F(xiàn)DDI, 100 Mbps ATM, and Fast Ethernet Transceivers in Low Cost 1x9 Package Style(800 nm 500 m，F(xiàn)DDI, 100 Mbps ATM, 快速以太網收發器（低價格 1x9 封裝類型）) |
| HFBR-5105T | 1300nm 500 m，F(xiàn)DDI, 100 Mbps ATM, and Fast Ethernet Transceivers in Low Cost 1x9 Package Style(1300nm 500 m，F(xiàn)DDI, 100 Mbps ATM, 快速以太網收發器（低價格 1x9 封裝類型）) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HFBR-4532Z | 功能描述:光纖連接器 Latching FO Crimples s Conn RoHS RoHS:否 制造商:Molex 產品:Adapters 類型:8 Port with External Shutter 連接器類型:Adapter 模式:Multimode 光纖直徑: 顏色:Blue 附件類型:LC Adapter |
| HFBR-4533 | 功能描述:光纖連接器 ACCESSORIES RoHS:否 制造商:Molex 產品:Adapters 類型:8 Port with External Shutter 連接器類型:Adapter 模式:Multimode 光纖直徑: 顏色:Blue 附件類型:LC Adapter |
| HFBR-4533Z | 功能描述:光纖連接器 ACCESSORIES RoHS RoHS:否 制造商:Molex 產品:Adapters 類型:8 Port with External Shutter 連接器類型:Adapter 模式:Multimode 光纖直徑: 顏色:Blue 附件類型:LC Adapter |
| HFBR-4535 | 功能描述:光纖連接器 Snap-In FO Cripmless Connector RoHS:否 制造商:Molex 產品:Adapters 類型:8 Port with External Shutter 連接器類型:Adapter 模式:Multimode 光纖直徑: 顏色:Blue 附件類型:LC Adapter |
| HFBR-4535Z | 功能描述:光纖連接器 Snap-In FO Connector Crimpless RoHS:否 制造商:Molex 產品:Adapters 類型:8 Port with External Shutter 連接器類型:Adapter 模式:Multimode 光纖直徑: 顏色:Blue 附件類型:LC Adapter |
發布緊急采購，3分鐘左右您將得到回復。