- 您現在的位置：買賣IC網 > PDF目錄361282 > HFBR-2532 1 MBd 600nm High Performance Link Receiver in Vertical Package PDF資料下載
參數資料
| 型號： | HFBR-2532 |
| 英文描述： | 1 MBd 600nm High Performance Link Receiver in Vertical Package |
| 中文描述： | 1 MBd的600納米高性能垂直連接的接收器包 |
| 文件頁數： | 6/11頁 |
| 文件大?。?/td> | 267K |
| 代理商： | HFBR-2532 |
6
Step 3
Any excess fiber protruding from
the connector end may be cut off;
however, the trimmed fiber
should extend at least 1.5 mm
(0.06 in) from the connector end.
Insert the connector fully into the
polishing fixture with the trimmed
fiber protruding from the bottom
of the fixture. This plastic polish-
ing fixture can be used to polish
two simplex connectors or simplex
latching connectors simultane-
ously, or one duplex connector.
Note:
The four dots on the
bottom of the polishing fixture
are wear indicators. Replace
the polishing fixture when any
dot is no longer visible.
Typically, the polishing fixture
can be used 10 times; 10 duplex
connectors or 20 simplex
connectors, two at a time.
Place the 600 grit abrasive paper
on a flat smooth surface, pressing
down on the connector, polish the
fiber and the connector using a
figure eight pattern of strokes
until the connector is flush with
the bottom of the polishing
fixture. Wipe the connector and
fixture with a clean cloth or
tissue.
Step 4
Place the flush connector and
polishing fixture on the dull side
of the 3
μ
m pink lapping film and
continue to polish the fiber and
connector for approximately 25
strokes. The fiber end should be
flat, smooth and clean.
This cable is now ready for use.
Note:
Use of the pink lapping
film fine polishing step results
in approximately 2 dB
improvement in coupling
performance of either a
transmitter-receiver link or a
bulkhead/splice over a 600 grit
polish alone. This fine polish is
comparable to the Agilent
factory polish. The fine
polishing step may be omitted
where an extra 2 dB of optical
power is not essential, as with
short link lengths. Proper
polishing of the tip of the fiber/
connector face results in a tip
diameter between 2.5 mm
(0.098 in.) minimum and 3.2
mm (0.126 in.) maximum..
HFBR-4593 Polishing Kit
相關PDF資料 |
PDF描述 |
|---|---|
| HFBR-2533 | 40 kBd 600nm Low Current/Extended Distance Link Receiver in Vertical Package |
| HFBR-4521 | HCS Fiber Connector - Black Simplex Connector/Crimp Ring |
| HFBR-END035 | Plastic Fiber Cable - Extra Low Loss. Standard Simplex Connector. Duplex Zipcord Cable. 35 Meters |
| HFBR-EUD500 | Plastic Fiber Cable - Extra Low Loss. Unconnectored. Duplex Zipcord Cable. 500 Meters |
| HFBR-EUS100 | Plastic Fiber Cable - Extra Low Loss. Unconnectored. Simplex Cable. 100 Meters |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HFBR-2532ET | 制造商:AVAGO 制造商全稱:AVAGO TECHNOLOGIES LIMITED 功能描述:Versatile Link The Versatile Fiber Optic Connection |
| HFBR-2532ETZ | 制造商:Avago Technologies 功能描述:VL VERT 1MBD RX ROHS EXT TEMP - Rail/Tube 制造商:Avago Technologies 功能描述:XMITTER FIBER OPTIC 制造商:Avago Technologies 功能描述:Fiber Optic Transmitters, Receivers, Transceivers VL VERT 1MBD RX ROHS EXT TEMP 制造商:Avago Technologies 功能描述:VL Vert 1MBd Rx RoHS Ext Temp 制造商:Avago Technologies 功能描述:TRANSCEIVER |
| HFBR-2532Z | 功能描述:光纖發射器、接收器、收發器 V-LINK VERTICAL 1MBd RCVR RoHS RoHS:否 制造商:Omron Electronics 產品:Transmitters 數據速率:3.5 Gbps 波長:850 nm 最大工作溫度: 最小工作溫度: 封裝 / 箱體: 封裝: |
| HFBR-2532Z | 制造商:Avago Technologies 功能描述:FIBRE OPTICS TRANSCEIVER MODULE DATA RA |
| HFBR2533 | 制造商:AGILENT 制造商全稱:AGILENT 功能描述:Versatile Link The Versatile Fiber Optic Connection |
發布緊急采購，3分鐘左右您將得到回復。