- 您現在的位置：買賣IC網 > PDF目錄353354 > HFBR-2522 The Versatile Fiber Optic Connection(438.45 k) PDF資料下載
參數資料
| 型號： | HFBR-2522 |
| 英文描述： | The Versatile Fiber Optic Connection(438.45 k) |
| 中文描述： | 多功能的光纖連接（438.45十一） |
| 文件頁數： | 2/16頁 |
| 文件大小： | 446K |
| 代理商： | HFBR-2522 |
10
Table 1. Pinout Table
Pin
Symbol
Functional Description
Mounting Pins The mounting pins are provided for transceiver mechanical attachment to the circuit board.
They are embedded in the nonconductive plastic housing and are not connected to the
transceiver internal circuit, nor is there a guaranteed connection to the metallized housing
in the EM and FM versions. They should be soldered into plated-through hole on the
printed circuit board.
1VEER
Receiver Signal Ground
Directly connect this pin to receiver signal ground plane. (For HFBR-53D3, VEER = VEET)
2
RD+
Receiver Data Out
RD+ is an open-emitter output circuit. Terminate this high-speed differential PECL output
with standard PECL techniques at the follow-on device input pin.
3RD–
Receiver Data Out Bar
RD– is an open-emitter output circuit. Terminate this high-speed differential PECL output
with standard PECL techniques at the follow-on device input pin.
4
SD
Signal Detect
Normal optical input levels to the receiver result in a logic “1” output, VOH, asserted.
Low input optical levels to the receiver result in a fault condition indicated by a logic “0”
output VOL, deasserted.
Signal Detect is a single-ended PECL output. SD can be terminated with standard PECL
techniques via 50
W to V
CCR - 2 V. Alternatively, SD can be loaded with a 270
W resistor to
VEER to conserve electrical power with small compromise to signal quality. If Signal Detect
output is not used, leave it open-circuited.
This Signal Detect output can be used to drive a PECL input on an upstream circuit, such
as, Signal Detect input or Loss of Signal-bar.
5VCCR
Receiver Power Supply
Provide +5 V dc via the recommended receiver power supply filter circuit.
Locate the power supply filter circuit as close as possible to the VCCR pin.
6VCCT
Transmitter Power Supply
Provide +5 Vdc via the recommended transmitter power supply filter circuit.
Locate the power supply filter circuit as close as possible to the VCCT pin.
7TD–
Transmitter Data In-Bar
Terminate this high-speed differential PECL input with standard PECL techniques at the
transmitter input pin.
8
TD+
Transmitter Data In
Terminate this high-speed differential PECL input with standard PECL techniques at the
transmitter input pin.
9VEET
Transmitter Signal Ground
Directly connect this pin to the transmitter signal ground plane.
Figure 2. Pin-Out
1 = V
EER
2 = RD+
3 = RD–
4 = SD
5 = V
CCR
6 = V
CCT
7 = TD–
8 = TD+
9 = V
EET
TOP VIEW
NIC
RX
TX
NIC = NO INTERNAL CONNECTION (MOUNTING PINS)
相關PDF資料 |
PDF描述 |
|---|---|
| HFBR-2528 | 10 MBd 650nm High Performance Link Receiver in Horizontal Package |
| HFBR-2602 | 2 MBd SERCOS Fiber Optic Receiver |
| HFBR-4663 | Fiber-Optic Transceiver |
| HFBR-5103 | FIBER OPTIC TRANSCEIVER，ML039MW025 |
| HFBR-5103A | 125 MBd ATM and Fast Ethernet Transceiver in Low Cost 1x9 Package: Extended Temp.. SC Receptacle |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HFBR-2522ET | 制造商:AVAGO 制造商全稱:AVAGO TECHNOLOGIES LIMITED 功能描述:Versatile Link The Versatile Fiber Optic Connection |
| HFBR-2522ETZ | 功能描述:光纖發射器、接收器、收發器 Versatile Link Horiz RoHS:否 制造商:Omron Electronics 產品:Transmitters 數據速率:3.5 Gbps 波長:850 nm 最大工作溫度: 最小工作溫度: 封裝 / 箱體: 封裝: |
| HFBR-2522Z | 功能描述:光纖發射器、接收器、收發器 V-LINK HORIZ 1MBd RC VR RoHS RoHS:否 制造商:Omron Electronics 產品:Transmitters 數據速率:3.5 Gbps 波長:850 nm 最大工作溫度: 最小工作溫度: 封裝 / 箱體: 封裝: |
| HFBR-2522Z | 制造商:Avago Technologies 功能描述:FIBRE OPTICS TRANSCEIVER MODULE LEADED |
| HFBR2523 | 制造商:Avago Technologies 功能描述:FIBRE OPTIC RECEIVER |
發布緊急采購，3分鐘左右您將得到回復。