- 您現在的位置：買賣IC網 > PDF目錄353187 > HFBR-2119T 266 MBd 1300 nm Fiber Optic Receiver with Plastic ST Connector PDF資料下載
參數資料
| 型號： | HFBR-2119T |
| 英文描述： | 266 MBd 1300 nm Fiber Optic Receiver with Plastic ST Connector |
| 中文描述： | 266 MBd的1300納米光纖接收器與塑料秘器 |
| 文件頁數： | 2/16頁 |
| 文件大?。?/td> | 446K |
| 代理商： | HFBR-2119T |
10
Table 1. Pinout Table
Pin
Symbol
Functional Description
Mounting Pins The mounting pins are provided for transceiver mechanical attachment to the circuit board.
They are embedded in the nonconductive plastic housing and are not connected to the
transceiver internal circuit, nor is there a guaranteed connection to the metallized housing
in the EM and FM versions. They should be soldered into plated-through hole on the
printed circuit board.
1VEER
Receiver Signal Ground
Directly connect this pin to receiver signal ground plane. (For HFBR-53D3, VEER = VEET)
2
RD+
Receiver Data Out
RD+ is an open-emitter output circuit. Terminate this high-speed differential PECL output
with standard PECL techniques at the follow-on device input pin.
3RD–
Receiver Data Out Bar
RD– is an open-emitter output circuit. Terminate this high-speed differential PECL output
with standard PECL techniques at the follow-on device input pin.
4
SD
Signal Detect
Normal optical input levels to the receiver result in a logic “1” output, VOH, asserted.
Low input optical levels to the receiver result in a fault condition indicated by a logic “0”
output VOL, deasserted.
Signal Detect is a single-ended PECL output. SD can be terminated with standard PECL
techniques via 50
W to V
CCR - 2 V. Alternatively, SD can be loaded with a 270
W resistor to
VEER to conserve electrical power with small compromise to signal quality. If Signal Detect
output is not used, leave it open-circuited.
This Signal Detect output can be used to drive a PECL input on an upstream circuit, such
as, Signal Detect input or Loss of Signal-bar.
5VCCR
Receiver Power Supply
Provide +5 V dc via the recommended receiver power supply filter circuit.
Locate the power supply filter circuit as close as possible to the VCCR pin.
6VCCT
Transmitter Power Supply
Provide +5 Vdc via the recommended transmitter power supply filter circuit.
Locate the power supply filter circuit as close as possible to the VCCT pin.
7TD–
Transmitter Data In-Bar
Terminate this high-speed differential PECL input with standard PECL techniques at the
transmitter input pin.
8
TD+
Transmitter Data In
Terminate this high-speed differential PECL input with standard PECL techniques at the
transmitter input pin.
9VEET
Transmitter Signal Ground
Directly connect this pin to the transmitter signal ground plane.
Figure 2. Pin-Out
1 = V
EER
2 = RD+
3 = RD–
4 = SD
5 = V
CCR
6 = V
CCT
7 = TD–
8 = TD+
9 = V
EET
TOP VIEW
NIC
RX
TX
NIC = NO INTERNAL CONNECTION (MOUNTING PINS)
相關PDF資料 |
PDF描述 |
|---|---|
| HFBR-2315M | FIBER OPTIC RECEIVER |
| HFBR-2315T | FIBER OPTIC RECEIVER |
| HFBR-2316T | 155 MBd 1300 nm Fiber Optic Receiver with Dual-in-line Package Panel-Mountable ST & SC Connector |
| HFBR-2402 | Low Cost. Miniature Fiber Optic Receiver with SMA Port - High Power |
| HFBR-2406 | Low Cost. Miniature Fiber Optic Receiver with SMA Port - Analog Output |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HFBR-2119TZ | 功能描述:光纖發射器、接收器、收發器 1300nm 266M 16pin DI P ST Rx Pbfree RoHS:否 制造商:Omron Electronics 產品:Transmitters 數據速率:3.5 Gbps 波長:850 nm 最大工作溫度: 最小工作溫度: 封裝 / 箱體: 封裝: |
| HFBR2125 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Optoelectronic |
| HFBR2202 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Optoelectronic |
| HFBR2204 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Optoelectronic |
| HFBR2208 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Optoelectronic |
發布緊急采購，3分鐘左右您將得到回復。