- 您現在的位置：買賣IC網 > PDF目錄370574 > HFBR-0300 1300 nm Fiber Optic Transmitter and Receiver(1300 nm 光纖傳送器和接收器) PDF資料下載
參數資料
| 型號： | HFBR-0300 |
| 英文描述： | 1300 nm Fiber Optic Transmitter and Receiver(1300 nm 光纖傳送器和接收器) |
| 中文描述： | 1300納米光纖發射器和接收器（1300納米光纖傳送器和接收器） |
| 文件頁數： | 5/8頁 |
| 文件大?。?/td> | 98K |
| 代理商： | HFBR-0300 |
5
Notes:
1. Typical data are at T
A
= 25
°
C.
2. Thermal resistance is measured with the transmitter coupled to a connector assembly and mounted on a printed circuit board;
Θ
JC
<
Θ
JA
.
3. Optical power is measured with a large area detector at the end of 1 meter of mode stripped cable, with an ST* precision ceramic
ferrule (MIL-STD-83522/13), which approximates a standard test connector. Average power measurements are made at 12.5 MHz
with a 50% duty cycle drive current of 0 to I
F,peak
; I
F,average
= I
F,peak
/2. Peak optical power is 3 dB higher than average optical
power.
4. When changing from
μ
W to dBm, the optical power is referenced to 1 mW (1000
μ
W).
Optical power P(dBm) = 10*log[P(
μ
W)/1000
μ
W].
5. Fiber NA is measured at the end of 2 meters of mode stripped fiber using the far-field pattern. NA is defined as the sine of the half
angle, determined at 5% of the peak intensity point. When using other manufacturer’s fiber cable, results will vary due to differing
NA values and test methods.
6. Overshoot is measured as a percentage of the peak amplitude of the optical waveform to the 100% amplitude level. The 100%
amplitude level is determined at the end of a 40 ns pulse, 50% duty cycle. This will ensure that ringing and other noise sources have
been eliminated.
7. Optical rise and fall times are measured from 10% to 90% with 62.5/125
μ
m fiber. LED response time with recommended test
circuit (Figure 3) at 25 MHz, 50% duty cycle.
8. 2.0 mm from where leads enter case.
Figure 2. Normalized Transmitter Output Power vs.
Forward Current.
Figure 1. Typical Forward Voltage and Current
Characteristics.
Figure 3. Recommended Transmitter Drive and Test Circuit.
100
1.1
1.2
1.3
1.4
1.5
1.6
V
F
– FORWARD VOLTAGE – V
I
F
90
80
70
60
50
40
20
30
1.2
10
30
50
70
90
I
F
– FORWARD CURRENT – mA
R
1.1
1.0
0.9
0.8
0.7
0.6
0.5
0.4
0.3
0.2
V = 0 V
6
V
O
2
3, 7
TEST
LOAD
≤
5 pF
500
100 pF
0.1
μ
F
V = -5 V
10
500
100 pF
0.1
μ
F
1 GHz FET PROBE
V = -5 V
HFBR-2316T
相關PDF資料 |
PDF描述 |
|---|---|
| HFBR-0305 | 1300 nm E-LED Transmitter and PIN/Preamp Receiver for Single-Mode Fiber(1300 nm 應用于單模式的E-LED傳送器和PIN/前置放大器接收器) |
| HFBR-0400 | Low Cost, Miniature Fiber Optic Components with ST， SMA, SC and FC Ports(帶ST，SMA, SC 和 FC端口的低價格，微型光纖元件) |
| HFBR-0600 | SERCOS Fiber Optic Transmitters and Receiver |
| HFBR-1115T | Fiber Optic Transmitter Data Links for 125 MBd(應用于125 MBd的光纖傳送數據鏈路) |
| HFBR-1116T | Fiber Optic Transmitter Data Links for 155 MBd(應用于155 MBd的光纖傳送數據鏈路) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HFBR-0305 | 制造商:64080 功能描述:FIBRE OPTICS, FIBRE OPTIC: K |
| HFBR-0310 | 功能描述:光學纖維開發工具 155 MBd Txcvr Evaluation Kit RoHS:否 制造商:Omron Electronics 產品:Evaluation Boards 用于:SX51 封裝: |
| HFBR-0310Z | 功能描述:光學纖維開發工具 125MBd 1300nm Evaluation Kit RoHS:否 制造商:Omron Electronics 產品:Evaluation Boards 用于:SX51 封裝: |
| HFBR-0319 | 功能描述:光學纖維開發工具 1X9 Fiber Optic Evaluation Kit RoHS:否 制造商:Omron Electronics 產品:Evaluation Boards 用于:SX51 封裝: |
| HFBR-0319 | 制造商:Avago Technologies 功能描述:Evaluation test fixture board |
發布緊急采購，3分鐘左右您將得到回復。