- 您現在的位置：買賣IC網 > PDF目錄223954 > HEDS-9140OPTIONF00 SINGLE, 3 CHANNELS, ROTARY OPTICAL POSITION ENCODER PDF資料下載
參數資料
| 型號： | HEDS-9140OPTIONF00 |
| 元件分類： | 編、解碼器及復用、解復用 |
| 英文描述： | SINGLE, 3 CHANNELS, ROTARY OPTICAL POSITION ENCODER |
| 封裝： | PLASTIC PACKAGE |
| 文件頁數： | 12/13頁 |
| 文件大小： | 276K |
| 代理商： | HEDS-9140OPTIONF00 |
8
Mounting with an Alignment Tool
The HEDS-8905 and HEDS-8906 alignment tools are rec-
ommended for mounting the modules with Side B as the
mounting plane. The HEDS-8905 is used to mount the
HEDS-9140, and the HEDS-8906 is used to mount the
HEDS-9040. These tools x the module position using
the codewheel hub as a reference. They will not work if
Side A is used as the mounting plane.
The following assembly procedure uses the HEDS-
8905/8906 alignment tool to mount a HEDS-9140/9040
module and a HEDS-5140/6140 codewheel:
Instructions:
1. Place codewheel on shaft.
2. Set codewheel height by placing alignment tool
on motor base (pins facing up) ush up against the
codewheel as shown in Figure 3. Tighten codewheel
setscrew and remove alignment tool.
3. Insert mounting screws through module and thread
into the motor base. Do not tighten screws.
4. Slide alignment tool over codewheel hub and onto
module as shown in Figure 4. The pins of the alignment
tool should t snugly inside the alignment recesses of
the module.
5. While holding alignment tool in place, tighten screws
down to secure module.
6. Remove alignment tool.
Mounting with Aligning Pins
The HEDS-9040 and HEDS-9140 can also be mounted us-
ing aligning pins on the motor base. (Hewlett-Packard
does not provide aligning pins.) For this conguration,
Side A must be used as the mounting plane. The align-
ing recess centers must be located within the 0.005 in. R
Tolerance Circle as explained above. Figure 5 shows the
necessary dimensions.
Figure 3. Alignment Tool is Used to Set Height of Codewheel.
Figure 4. Alignment Tool is Placed over Shaft and onto Codewheel Hub.
Alignment Tool Pins Mate with Aligning Recesses on Module.
相關PDF資料 |
PDF描述 |
|---|---|
| HEDS-9140OPTIONI00 | SINGLE, 3 CHANNELS, ROTARY OPTICAL POSITION ENCODER |
| HEDS-9700OPTIONG50 | SINGLE, 2 CHANNELS, ROTARY OPTICAL POSITION ENCODER |
| HEDS-9700OPTIONK51 | SINGLE, 2 CHANNELS, ROTARY OPTICAL POSITION ENCODER |
| HEDS-9781H50 | SINGLE, 2 CHANNELS, ROTARY/LINEAR OPTICAL POSITION ENCODER |
| HEN1F308X-N | 8 CONTACT(S), AVIONAL, FEMALE, CIRCULAR CONNECTOR, SOLDER, RECEPTACLE |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HEDS-9141#A00 | 功能描述:編碼器 3 Channel 500CPR RoHS:否 制造商:Avago Technologies 產品:Optical Encoders 類型:Absolute 每轉脈沖: 制動器數量: 通道數量:2 安裝風格:Through Hole 端接類型:Solder Pin 輸出: 軸類型: 帶開關: 電源電壓:5 V 工作溫度范圍:- 40 C to + 115 C |
| HEDS-9141#E00 | 功能描述:編碼器 3 Channel 200CPR RoHS:否 制造商:Avago Technologies 產品:Optical Encoders 類型:Absolute 每轉脈沖: 制動器數量: 通道數量:2 安裝風格:Through Hole 端接類型:Solder Pin 輸出: 軸類型: 帶開關: 電源電壓:5 V 工作溫度范圍:- 40 C to + 115 C |
| HEDS-9141#F00 | 功能描述:編碼器 3 Channel 256CPR RoHS:否 制造商:Avago Technologies 產品:Optical Encoders 類型:Absolute 每轉脈沖: 制動器數量: 通道數量:2 安裝風格:Through Hole 端接類型:Solder Pin 輸出: 軸類型: 帶開關: 電源電壓:5 V 工作溫度范圍:- 40 C to + 115 C |
| HEDS-9141#G00 | 功能描述:編碼器 3 Channel 360CPR RoHS:否 制造商:Avago Technologies 產品:Optical Encoders 類型:Absolute 每轉脈沖: 制動器數量: 通道數量:2 安裝風格:Through Hole 端接類型:Solder Pin 輸出: 軸類型: 帶開關: 電源電壓:5 V 工作溫度范圍:- 40 C to + 115 C |
| HEDS-9141-C00 | 制造商:Avago Technologies 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。