- 您現在的位置：買賣IC網 > PDF目錄223954 > HEDS-5600#E06 SINGLE, 2 CHANNELS, ROTARY OPTICAL POSITION ENCODER PDF資料下載
參數資料
| 型號： | HEDS-5600#E06 |
| 元件分類： | 編、解碼器及復用、解復用 |
| 英文描述： | SINGLE, 2 CHANNELS, ROTARY OPTICAL POSITION ENCODER |
| 文件頁數： | 12/12頁 |
| 文件大?。?/td> | 1635K |
| 代理商： | HEDS-5600#E06 |
9
Encoder Mounting and Assembly
1a. For HEDS-5500 and 5600: Mount encoder base plate
onto motor. Tighten screws. Go on to step 2.
1b. For HEDS-5540, 5640 and HEDM-5500, 5600, 5540 :
Slip alignment tool onto motor shaft. With alignment
tool in place, mount encoder baseplate onto motor
as shown above. Tighten screws. Remove alignment
tool.
1c. It is recommended that adhesive* is applied to the
screw-baseplate interface to prevent screw loosening
due to effect of high temperature on plastic
2. Snap encoder body onto base plate locking all 4
snaps.
a. Push the hex wrench into the body of the encoder to
ensure that it is properly seated into the code wheel
hub set screws. Then apply a downward force on the
end of the hex wrench. This sets the code wheel gap
by levering the code wheel hub to its upper position.
b. While continuing to apply a downward force, rotate
the hex wrench in the clockwise direction until the
hub set screw is tight against the motor shaft (The
recommended torque to tighten the setscrew is 15-
18 ozf.inch). The hub set screw attaches the code
wheel to the motor’s shaft.
c. Remove the hex wrench by pulling it straight out of
the encoder body.
4. Use the center screwdriver slot, or either of the two
side slots, to rotate the encoder cap dot clockwise
from the one dot position to the two dot position. Do
not rotate the encoder cap counterclockwise beyond
the one dot position.
The encoder is ready for use!
相關PDF資料 |
PDF描述 |
|---|---|
| HEDS-6540B13 | SINGLE, 3 CHANNELS, ROTARY OPTICAL POSITION ENCODER |
| HEDM-6500U06 | SINGLE, 2 CHANNELS, ROTARY OPTICAL POSITION ENCODER |
| HEDS-9140-OPTION-F00 | SINGLE, 3 CHANNELS, ROTARY OPTICAL POSITION ENCODER |
| HEDS-9140OPTIONF00 | SINGLE, 3 CHANNELS, ROTARY OPTICAL POSITION ENCODER |
| HEDS-9140OPTIONI00 | SINGLE, 3 CHANNELS, ROTARY OPTICAL POSITION ENCODER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HEDS5605 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:QUADRANT/CIRCULAR DETECTOR |
| HEDS-5605#A06 | 功能描述:編碼器 2 Channel 500 CPR 1/4in Metal CW RoHS:否 制造商:Avago Technologies 產品:Optical Encoders 類型:Absolute 每轉脈沖: 制動器數量: 通道數量:2 安裝風格:Through Hole 端接類型:Solder Pin 輸出: 軸類型: 帶開關: 電源電壓:5 V 工作溫度范圍:- 40 C to + 115 C |
| HEDS-5605#A13 | 功能描述:編碼器 2 Channel 500 CPR 8mm Metal CW RoHS:否 制造商:Avago Technologies 產品:Optical Encoders 類型:Absolute 每轉脈沖: 制動器數量: 通道數量:2 安裝風格:Through Hole 端接類型:Solder Pin 輸出: 軸類型: 帶開關: 電源電壓:5 V 工作溫度范圍:- 40 C to + 115 C |
| HEDS-5605#C06 | 功能描述:編碼器 2 Channel 100 CPR 1/4in Metal CW RoHS:否 制造商:Avago Technologies 產品:Optical Encoders 類型:Absolute 每轉脈沖: 制動器數量: 通道數量:2 安裝風格:Through Hole 端接類型:Solder Pin 輸出: 軸類型: 帶開關: 電源電壓:5 V 工作溫度范圍:- 40 C to + 115 C |
| HEDS-5605#E06 | 功能描述:編碼器 2 Channel 200 CPR 1/4in Metal CW RoHS:否 制造商:Avago Technologies 產品:Optical Encoders 類型:Absolute 每轉脈沖: 制動器數量: 通道數量:2 安裝風格:Through Hole 端接類型:Solder Pin 輸出: 軸類型: 帶開關: 電源電壓:5 V 工作溫度范圍:- 40 C to + 115 C |
發布緊急采購，3分鐘左右您將得到回復。