- 您現在的位置：買賣IC網 > PDF目錄365057 > HEDM-5500-B13 Quick Assembly Two and Three Channel Optical Encoders PDF資料下載
參數資料
| 型號： | HEDM-5500-B13 |
| 英文描述： | Quick Assembly Two and Three Channel Optical Encoders |
| 中文描述： | 快速大會二及中三通道光學編碼器 |
| 文件頁數： | 7/15頁 |
| 文件大?。?/td> | 291K |
| 代理商： | HEDM-5500-B13 |
第1頁第2頁第3頁第4頁第5頁第6頁當前第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁
7
Electrical Interface
To insure reliable encoding
performance, the HEDS-5540 and
5640 three channel encoders
require 2.7 k
(
±
10%) pull-up
resistors on output pins 2, 3, and
5 (Channels I, A, and B) as shown
in Figure 1. These pull-up
resistors should be located as
close to the encoder as possible
(within 4 feet). Each of the three
encoder outputs can drive a single
TTL load in this configuration.
The HEDS-5500, 5600, and
HEDM-5500, 5600 two channel
encoders do not normally require
pull-up resistors. However, 3.2 k
pull-up resistors on output pins 3
and 5 (Channels A and B) are
recommended to improve rise
times, especially when operating
above 100 kHz frequencies.
Mechanical Characteristics
Parameter
Symbol
Dimension
Tolerance
[1]
Units
Codewheel Fits These
Standard Shaft Diameters
2
5
3
6
4
8
+0.000
-0.015
mm
5/32
3/16
1/8
1/4
+0.0000
-0.0007
in
Moment of Inertia
J
0.6 (8.0 x 10
-6
)
g-cm
2
(oz-in-s
2
)
Required Shaft Length
[2]
14.0 (0.55)
±
0.5
(
±
0.02)
mm
(in.)
Bolt Circle
[3]
2 screw
mounting
19.05
(0.750)
±
0.13
(
±
0.005)
mm
(in.)
3 screw
mounting
20.90
(0.823)
±
0.13
(
±
0.005)
mm
(in.)
external
mounting ears
46.0
(1.811)
±
0.13
(
±
0.005)
mm
(in.)
Mounting Screw Size
[4]
2 screw
mounting
M 2.5 or (2-56)
mm (in.)
3 screw
mounting
M 1.6 or (0-80)
mm (in.)
external
mounting ears
M 2.5 or (2-56)
mm (in.)
Encoder Base Plate
Thickness
0.33 (0.130)
mm (in.)
Hub Set Screw
(2-56)
(in.)
Notes:
1. These are tolerances required of the user.
2. The HEDS-55X5 and 56X5, HEDM-5505, 5605 provide an 8.9 mm (0.35 inch) diameter hole through the housing for longer motor
shafts. See Ordering Information.
3. The HEDS-5540 and 5640 must be aligned using the aligning pins as specified in Figure 3, or using the alignment tool as shown in
“Encoder Mounting and Assembly”. See also “Mounting Considerations.”
4. The recommended mounting screw torque for 2 screw and external ear mounting is 1.0 kg-cm (0.88 in-lbs). The recommended
mounting screw torque for 3 screw mounting is 0.50 kg-cm (0.43 in-lbs).
相關PDF資料 |
PDF描述 |
|---|---|
| HEDM-5500-B14 | Quick Assembly Two and Three Channel Optical Encoders |
| HEDM-5500-J04 | Quick Assembly Two and Three Channel Optical Encoders |
| HEDM-5500-J05 | Quick Assembly Two and Three Channel Optical Encoders |
| HEDM-5500-J06 | Quick Assembly Two and Three Channel Optical Encoders |
| HEDM-5500-J11 | Quick Assembly Two and Three Channel Optical Encoders |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HEDM-5500-B14 | 制造商:AGILENT 制造商全稱:AGILENT 功能描述:Quick Assembly Two and Three Channel Optical Encoders |
| HEDM-5500-J01 | 制造商:HP 制造商全稱:Agilent(Hewlett-Packard) 功能描述:Quick Assembly Two and Three Channel Optical Encoders |
| HEDM-5500-J02 | 制造商:AGILENT 制造商全稱:AGILENT 功能描述:Quick Assembly Two and Three Channel Optical Encoders |
| HEDM-5500-J03 | 制造商:HP 制造商全稱:Agilent(Hewlett-Packard) 功能描述:Quick Assembly Two and Three Channel Optical Encoders |
| HEDM-5500-J04 | 制造商:AGILENT 制造商全稱:AGILENT 功能描述:Quick Assembly Two and Three Channel Optical Encoders |
發布緊急采購，3分鐘左右您將得到回復。