- 您現在的位置：買賣IC網 > PDF目錄371798 > HDSP-253 Eight Character 5 mm Smart Alphanumeric Display PDF資料下載
參數資料
| 型號： | HDSP-253 |
| 英文描述： | Eight Character 5 mm Smart Alphanumeric Display |
| 中文描述： | 八字5毫米智能字符顯示 |
| 文件頁數： | 10/16頁 |
| 文件大?。?/td> | 201K |
| 代理商： | HDSP-253 |
10
UDC RAM and UDC Address
Register
Figure 3 shows the logic levels
needed to access the UDC RAM
and the UDC Address Register.
The UDC Address Register is
eight bits wide. The lower four
bits (D
0
-D
3
) are used to select one
of the 16 UDC locations. The
upper four bits (D
4
-D
7
) are not
used. Once the UDC address has
been stored in the UDC Address
Register, the UDC RAM can be
accessed.
To completely specify a 5 x 7
character requires eight write
cycles. One cycle is used to store
the UDC RAM address in the UDC
Address Register. Seven cycles
are used to store dot data in the
UDC RAM. Data is entered by
rows. One cycle is needed to
access each row. Figure 4 shows
the organization of a UDC
character assuming the symbol to
be stored is an “F.” A
0
-A
2
are used
to select the row to be accessed
and D
0
-D
4
are used to transmit
the row dot data. The upper three
bits (D
5
-D
7
) are ignored. D
0
(least
significant bit) corresponds to the
right most column of the 5 x 7
matrix and D
4
(most significant
bit) corresponds to the left most
column of the 5 x 7 matrix.
Flash RAM
Figure 5 shows the logic levels
needed to access the Flash RAM.
The Flash RAM has one bit
associated with each location of
the Character RAM. The Flash
input is used to select the Flash
RAM. Address lines A
3
-A
4
are
ignored. Address lines A
0
-A
2
are
used to select the location in the
Flash RAM to store the attribute.
D
0
is used to store or remove the
flash attribute. D
0
= “1” stores
the attribute and D
0
= “0”
removes the attribute.
When the attribute is enabled
through bit 3 of the Control Word
and a “1” is stored in the Flash
RAM, the corresponding
character will flash at approxi-
mately 2 Hz. The actual rate is
dependent on the clock frequency.
For an external clock the flash
rate can be calculated by dividing
the clock frequency by 28,672.
Figure 3. Logic Levels to Access a UDC Character.
Figure 4. Data to Load ""F'' into the UDC RAM.
相關PDF資料 |
PDF描述 |
|---|---|
| HDSP-3906 | 20 mm (0.8 inch) Seven Segment Displays |
| HDSP-8601 | 20 mm (0.8 inch) Seven Segment Displays |
| HDSP-8603 | 20 mm (0.8 inch) Seven Segment Displays |
| HDSP-8605 | Replaced by SN75ALS174A : Quadruple Differential Line Drivers 20-SOIC |
| HDSP-8606 | Replaced by SN75ALS174A : Quadruple Differential Line Drivers 16-PDIP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HDSP-2530 | 功能描述:LED 顯示器和配件 Orange 602nm 5x7 Smart Display RoHS:否 制造商:Avago Technologies 顯示器類型:7 Segment 數位數量:2 字符大小:7.8 mm x 14.22 mm 照明顏色:Red 波長:628 nm 共用管腳:Common Anode 工作電壓:2.05 V 工作電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 35 C 封裝:Tube |
| HDSP-2531 | 功能描述:LED 顯示器和配件 Yellow 585nm 5x7 Smart Display RoHS:否 制造商:Avago Technologies 顯示器類型:7 Segment 數位數量:2 字符大小:7.8 mm x 14.22 mm 照明顏色:Red 波長:628 nm 共用管腳:Common Anode 工作電壓:2.05 V 工作電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 35 C 封裝:Tube |
| HDSP-2532 | 功能描述:LED 顯示器和配件 Red 626nm 5x7 Smart Display RoHS:否 制造商:Avago Technologies 顯示器類型:7 Segment 數位數量:2 字符大小:7.8 mm x 14.22 mm 照明顏色:Red 波長:628 nm 共用管腳:Common Anode 工作電壓:2.05 V 工作電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 35 C 封裝:Tube |
| HDSP-2533 | 功能描述:LED 顯示器和配件 Green 574nm 5x7 Smart Display RoHS:否 制造商:Avago Technologies 顯示器類型:7 Segment 數位數量:2 字符大小:7.8 mm x 14.22 mm 照明顏色:Red 波長:628 nm 共用管腳:Common Anode 工作電壓:2.05 V 工作電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 35 C 封裝:Tube |
| HDSP2533 | 制造商:Avago Technologies 功能描述:LED DISPLAY ALPHANUMERIC |
發布緊急采購，3分鐘左右您將得到回復。