- 您現在的位置：買賣IC網 > PDF目錄367056 > HD-1900M3-CH (Hirose Electric USA, INC.) 3 dB 90∑ Card Couplers PDF資料下載
參數資料
| 型號： | HD-1900M3-CH |
| 廠商： | Hirose Electric USA, INC. |
| 英文描述： | 3 dB 90∑ Card Couplers |
| 中文描述： | 3分貝90Σ卡耦合器 |
| 文件頁數： | 8/9頁 |
| 文件大?。?/td> | 584K |
| 代理商： | HD-1900M3-CH |
34
I
Mounting Method
Figure 1.
Figure 3.
Figure 4.
Fastening screw
Microstrip board
Micro stripline
Tab
Figure 2.
The three types of mounting methods
illustrated in the diagrams below will
mount the card coupler for use under
optimum conditions.
The fastening screws in the diagrams
are M2 screws tightened to 1.5 kg
cm.
When the tip of the micro stripline is of
Teflon type material ( r = 2.6), C
chamfering of C1 is performed at t1.6,
and of C0.5 at t1.2.
The side view diagrams of Figure 1 are
illustrated in Figures 2, 3, and 4 below.
Gap S between the card coupler and
the microstrip board surface should be
used to agree with the following
conditions.
Below 500 MHz........S
≤
0.5 mm
500 to 2300 MHz......S
≤
0.25 mm
Above 2300 MHz......S
≤
0.15 mm
Metal plate or conductive spacer
G
When the Ground Board is Constructed of 0.4 mm Stainless and 0.8 mm Aluminum
(When the Thickness of the Microstrip Board is 1.6 or 1.2 mm)
For t1.6 boards, use with the stainless case of the card coupler facing upward. For t1.2 boards,
use with the aluminum case of the card coupler facing upward. Mount and fix the card coupler
with fastening screws as illustrated in Figure 2. Next, solder the tabs and micro stripline, then
use.
(When the Thickness of the Microstrip Board is Greater than 1.6 mm)
Insert a metal plate or a conductive spacer between the coupler and ground, then mount as
illustrated in Figure 3 so that the surface of the tabs and the position of the microstrip board are
equal. Fix the card coupler with fastening screws as illustrated in Figure 3. Next, solder the tabs
and micro stripline, then use.
(When the Thickness of the Microstrip Board is Less than 1.2 mm)
Cut the ground at the position of the coupler and attach so that the surface of the tabs is in
contact with the micro stripline. Fix the card coupler with fastening screws as illustrated in Figure
4. Next, solder the tabs and micro stripline, then use.
∏
相關PDF資料 |
PDF描述 |
|---|---|
| HD-2100M3-CH | 3 dB 90∑ Card Couplers |
| HD-2500M3-BH | 3 dB 90∑ Card Couplers |
| HD-3200M3-BH | 3 dB 90∑ Card Couplers |
| HD-3900M3-BH | 3 dB 90∑ Card Couplers |
| HD-02103AST | SCR Thyristor; Thyristor Type:Sensitive Gate; Peak Repetitive Off-State Voltage, Vdrm:60V; On-State RMS Current, IT(rms):800mA; Peak Non Repetitive Surge Current, Itsm:8A; Gate Trigger Current Max, Igt:200uA |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HD19-1 | 功能描述:HARDWARE KIT CM90 SERIES RoHS:是 類別:盒，外殼，支架 >> 卡架 - 配件 系列:- 標準包裝:1 系列:VectorPak™ 附件類型:EFP 模塊 適用于相關產品:PCB |
| HD1929 | 制造商: 功能描述:1929 |
| HD1A3M | 制造商:NEC 制造商全稱:NEC 功能描述:on-chip resistor NPN silicon epitaxial transistor For mid-speed switching |
| HD1A3M-T1-AZ | 制造商:Renesas Electronics Corporation 功能描述: |
| HD1A4A | 制造商:NEC 制造商全稱:NEC 功能描述:on-chip resistor NPN silicon epitaxial transistor For mid-speed switching |
發布緊急采購，3分鐘左右您將得到回復。