參數資料
型號: HCPL4100
英文描述: Optically Coupled 20 mA Current Loop Transmitter
中文描述: 光耦合20毫安電流回路變送器
文件頁數: 11/12頁
文件大小: 230K
代理商: HCPL4100
11
As Figure 15 illustrates, the
combination of Agilent current
loop optocouplers, HCPL-4100
transmitter and HCPL-4200
receiver, can be used at the
isolated end of current loops.
Cross talk and common mode
coupling are greatly reduced
when optical isolation is imple-
mented at the same end of both
loops, as shown. Full duplex data
rate is limited by the non-isolated
active transmitter current loop.
Comments mentioned under
simplex configuration apply to
the full duplex case. Consult the
HCPL-4200 receiver optocoupler
data sheet for specified device
performance.
Half Duplex
The half duplex configuration,
whether point to point or multi-
drop, gives non-simultaneous
bidirectional data flow from
transmitters to transmitters
shown in Figures 16a and 16b.
This configuration allows the use
of two wires to carry data back
and forth between local and
remote units. However, protocol
must be used to determine which
specific transmitter can operate
at any given time. Maximum data
rate for a half duplex system is
limited by the loop current
charging time. These considera-
tions were explained in the
Simplex configuration section.
Figures 16a and 16b illustrate
half duplex application for the
combination of HCPL-4100/-4200
optocouplers. The unique and
complementary designs of the
HCPL-4100 transmitter and
HCPL-4200 receiver optocoup-
lers provide many designed-in
benefits. For example, total
optical isolation at one end of the
current loop is easily accom-
plished, which results in
substantial removal of common
mode influences, elimination of
ground potential differences and
reduction of power supply
requirements. With this combina-
tion of HCPL-4100/-4200 opto-
couplers, specific current loop
noise immunity is provided, i.e.,
minimum SPACE state current
noise immunity is 1 mA, MARK
state noise immunity is 8 mA.
Voltage compliance of the current
source must be of an adequate
level for operating all units in the
loop while not exceeding 27 V dc,
the maximum breakdown voltage
for the HCPL-4100. Note that the
HCPL-4100 transmitter will allow
output loop current to conduct
when input V
CC
power is off.
Consult the HCPL-4200 receiver
optocoupler data sheet for
specified device performance.
For more information about the
HCPL-4100/-4200 optocouplers,
consult Application Note 1018.
Figure 15. Full Duplex Point to Point Current Loop System Configuration.
相關PDF資料
PDF描述
HCPL-4100 Optically Coupled 20 mA Optically Coupled 20 mA
HCPL-4534 Dual Channel, High Speed Optocouplers
HCPL2530 Dual Channel, High Speed Optocouplers
HCPL-0530 Dual Channel, High Speed Optocouplers
HCPL-0531 Dual Channel, High Speed Optocouplers
相關代理商/技術參數
參數描述
HCPL-4100 功能描述:邏輯輸出光電耦合器 20mA Current Loop RoHS:否 制造商:Fairchild Semiconductor 絕緣電壓:4243 Vrms 輸出類型:Push-Pull 最大傳播延遲時間:500 ns 最大正向二極管電壓: 最大反向二極管電壓: 最大正向二極管電流: 最大連續輸出電流:2.5 A 最大功率耗散:100 mW 最大工作溫度:+ 100 C 最小工作溫度:- 40 C 封裝 / 箱體:SO-16 封裝:Tube
HCPL-4100#300 功能描述:邏輯輸出光電耦合器 20mA Current Loop RoHS:否 制造商:Fairchild Semiconductor 絕緣電壓:4243 Vrms 輸出類型:Push-Pull 最大傳播延遲時間:500 ns 最大正向二極管電壓: 最大反向二極管電壓: 最大正向二極管電流: 最大連續輸出電流:2.5 A 最大功率耗散:100 mW 最大工作溫度:+ 100 C 最小工作溫度:- 40 C 封裝 / 箱體:SO-16 封裝:Tube
HCPL-4100#500 功能描述:邏輯輸出光電耦合器 20mA Current Loop RoHS:否 制造商:Fairchild Semiconductor 絕緣電壓:4243 Vrms 輸出類型:Push-Pull 最大傳播延遲時間:500 ns 最大正向二極管電壓: 最大反向二極管電壓: 最大正向二極管電流: 最大連續輸出電流:2.5 A 最大功率耗散:100 mW 最大工作溫度:+ 100 C 最小工作溫度:- 40 C 封裝 / 箱體:SO-16 封裝:Tube
HCPL-4100-000E 功能描述:邏輯輸出光電耦合器 20mA Current Loop RoHS:否 制造商:Fairchild Semiconductor 絕緣電壓:4243 Vrms 輸出類型:Push-Pull 最大傳播延遲時間:500 ns 最大正向二極管電壓: 最大反向二極管電壓: 最大正向二極管電流: 最大連續輸出電流:2.5 A 最大功率耗散:100 mW 最大工作溫度:+ 100 C 最小工作溫度:- 40 C 封裝 / 箱體:SO-16 封裝:Tube
HCPL-4100-000E 制造商:Avago Technologies 功能描述:CURRENT LOOP OPTOCOUPLER(20MA) LF - LE