- 您現在的位置：買賣IC網 > PDF目錄370451 > HCPL3150 0.5 Amp Output Current IGBT Gate Drive Optocoupler PDF資料下載
參數資料
| 型號： | HCPL3150 |
| 英文描述： | 0.5 Amp Output Current IGBT Gate Drive Optocoupler |
| 中文描述： | 0.5安培輸出電流IGBT柵極驅動光電耦合器 |
| 文件頁數： | 13/15頁 |
| 文件大?。?/td> | 253K |
| 代理商： | HCPL3150 |
1-209
T
JE
= LED junction temperature
T
JD
= detector IC junction temperature
T
C
= case temperature measured at the center of the package bottom
θ
LC
= LED-to-case thermal resistance
θ
LD
= LED-to-detector thermal resistance
θ
DC
= detector-to-case thermal resistance
θ
CA
= case-to-ambient thermal resistance
θ
CA
will depend on the board design and the placement of the part.
CMR with the LED On
(CMR
H
)
A high CMR LED drive circuit
must keep the LED on during
common mode transients. This is
achieved by overdriving the LED
current beyond the input
threshold so that it is not pulled
below the threshold during a
transient. A minimum LED cur-
rent of 10 mA provides adequate
margin over the maximum I
FLH
of
5 mA to achieve 15 kV/
μ
s CMR.
CMR with the LED Off
(CMR
L
)
A high CMR LED drive circuit
must keep the LED off
(V
F
≤
V
F(OFF)
) during common
mode transients. For example,
during a -dV
CM
/dt transient in
Figure 31, the current flowing
through C
LEDP
also flows through
the R
SAT
and V
SAT
of the logic
gate. As long as the low state
voltage developed across the
logic gate is less than V
F(OFF)
, the
LED will remain off and no
common mode failure will occur.
The open collector drive circuit,
shown in Figure 32, cannot keep
the LED off during a +dV
CM
/dt
transient, since all the current
flowing through C
LEDN
must be
supplied by the LED, and it is not
recommended for applications
requiring ultra high CMR
L
performance. Figure 33 is an
alternative drive circuit which,
like the recommended application
circuit (Figure 25), does achieve
ultra high CMR performance by
shunting the LED in the off state.
Under Voltage Lockout
Feature
The HCPL-3150 contains an
under voltage lockout (UVLO)
feature that is designed to protect
the IGBT under fault conditions
which cause the HCPL-3150
supply voltage (equivalent to the
fully-charged IGBT gate voltage)
to drop below a level necessary to
keep the IGBT in a low resistance
state. When the HCPL-3150
output is in the high state and the
supply voltage drops below the
HCPL-3150 V
UVLO-
threshold
(9.5 <V
UVLO-
<12.0), the
optocoupler output will go into
the low state with a typical delay,
UVLO Turn Off Delay, of 0.6
μ
s.
When the HCPL-3150 output is in
the low state and the supply
voltage rises above the HCPL-
3150 V
UVLO+
threshold
(11.0 < V
UVLO+
< 13.5), the
optocoupler will go into the high
state (assuming LED is “ON”)
with a typical delay, UVLO TURN
On Delay, of 0.8
μ
s.
IPM Dead Time and
Propagation Delay
Specifications
The HCPL-3150 includes a
Propagation Delay Difference
(PDD) specification intended to
help designers minimize “dead
time” in their power inverter
designs. Dead time is the time
period during which both the
high and low side power
transistors (Q1 and Q2 in Figure
25) are off. Any overlap in Q1
and Q2 conduction will result in
large currents flowing through
the power devices from the high-
to the low-voltage motor rails.
To minimize dead time in a given
design, the turn on of LED2
should be delayed (relative to the
Figure 28. Thermal Model.
θ
LD
= 439°C/W
T
JE
T
JD
θ
LC
= 391°C/W
θ
DC
= 119°C/W
θ
CA
= 83°C/W*
T
C
T
A
相關PDF資料 |
PDF描述 |
|---|---|
| HCPL-3150 | Single Channel 0.5 Amp Output Current IGBT Gate Drive Optocoupler(單通道 0.5 Amp輸出電流 IGBT門驅動耦合器) |
| HCPL-315J | Dual Channel 0.5 Amp Output Current IGBT Gate Drive Optocoupler(雙通道 0.5 Amp輸出電流 IGBT門驅動耦合器) |
| HCPL-316J | 2.0 Amp Gate Drive Optocoupler with Integrated (V CE ) Desaturation Detection and Fault Status Feedback(帶集成不飽和檢測和誤差反饋的2.0 Amp門驅動耦合器) |
| HCPL-3700 | AC/DC to Logic Interface Optocouplers(AC/DC邏輯接口光耦合器) |
| HCPL-4100300 | Optically Coupled 20 mA Current Loop Transmitter |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HCPL-3150 | 功能描述:邏輯輸出光電耦合器 0.5A IGBT Gate Drive RoHS:否 制造商:Fairchild Semiconductor 絕緣電壓:4243 Vrms 輸出類型:Push-Pull 最大傳播延遲時間:500 ns 最大正向二極管電壓: 最大反向二極管電壓: 最大正向二極管電流: 最大連續輸出電流:2.5 A 最大功率耗散:100 mW 最大工作溫度:+ 100 C 最小工作溫度:- 40 C 封裝 / 箱體:SO-16 封裝:Tube |
| HCPL-3150#060 | 功能描述:邏輯輸出光電耦合器 0.5A IGBT Gate Drive RoHS:否 制造商:Fairchild Semiconductor 絕緣電壓:4243 Vrms 輸出類型:Push-Pull 最大傳播延遲時間:500 ns 最大正向二極管電壓: 最大反向二極管電壓: 最大正向二極管電流: 最大連續輸出電流:2.5 A 最大功率耗散:100 mW 最大工作溫度:+ 100 C 最小工作溫度:- 40 C 封裝 / 箱體:SO-16 封裝:Tube |
| HCPL-3150#300 | 功能描述:邏輯輸出光電耦合器 0.5A IGBT Gate Drive RoHS:否 制造商:Fairchild Semiconductor 絕緣電壓:4243 Vrms 輸出類型:Push-Pull 最大傳播延遲時間:500 ns 最大正向二極管電壓: 最大反向二極管電壓: 最大正向二極管電流: 最大連續輸出電流:2.5 A 最大功率耗散:100 mW 最大工作溫度:+ 100 C 最小工作溫度:- 40 C 封裝 / 箱體:SO-16 封裝:Tube |
| HCPL-3150#360 | 功能描述:邏輯輸出光電耦合器 0.5A IGBT Gate Drive RoHS:否 制造商:Fairchild Semiconductor 絕緣電壓:4243 Vrms 輸出類型:Push-Pull 最大傳播延遲時間:500 ns 最大正向二極管電壓: 最大反向二極管電壓: 最大正向二極管電流: 最大連續輸出電流:2.5 A 最大功率耗散:100 mW 最大工作溫度:+ 100 C 最小工作溫度:- 40 C 封裝 / 箱體:SO-16 封裝:Tube |
| HCPL-3150#500 | 功能描述:邏輯輸出光電耦合器 0.5A IGBT Gate Drive RoHS:否 制造商:Fairchild Semiconductor 絕緣電壓:4243 Vrms 輸出類型:Push-Pull 最大傳播延遲時間:500 ns 最大正向二極管電壓: 最大反向二極管電壓: 最大正向二極管電流: 最大連續輸出電流:2.5 A 最大功率耗散:100 mW 最大工作溫度:+ 100 C 最小工作溫度:- 40 C 封裝 / 箱體:SO-16 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。