- 您現在的位置：買賣IC網 > PDF目錄370451 > HCPL-315J Dual Channel 0.5 Amp Output Current IGBT Gate Drive Optocoupler(雙通道 0.5 Amp輸出電流 IGBT門驅動耦合器) PDF資料下載
參數資料
| 型號： | HCPL-315J |
| 英文描述： | Dual Channel 0.5 Amp Output Current IGBT Gate Drive Optocoupler(雙通道 0.5 Amp輸出電流 IGBT門驅動耦合器) |
| 中文描述： | 雙通道0.5安培的輸出電流IGBT柵極驅動光電耦合器（雙通道0.5安培輸出電流IGBT的門驅動耦合器） |
| 文件頁數： | 17/20頁 |
| 文件大小： | 320K |
| 代理商： | HCPL-315J |
17
CMR with the LED On
(CMR
H
)
A high CMR LED drive circuit
must keep the LED on during
common mode transients. This is
achieved by overdriving the LED
current beyond the input
threshold so that it is not pulled
below the threshold during a
transient. A minimum LED cur-
rent of 10 mA provides adequate
margin over the maximum I
FLH
of
5 mA to achieve 15 kV/
μ
s CMR.
CMR with the LED Off
(CMR
L
)
A high CMR LED drive circuit
must keep the LED off
(V
F
≤
V
F(OFF)
) during common
mode transients. For example,
during a -dV
CM
/dt transient in
Figure 31, the current flowing
through C
LEDP
also flows through
the R
SAT
and V
SAT
of the logic
gate. As long as the low state
voltage developed across the
Figure 27. Energy Dissipated in the
HCPL-3150 for Each IGBT Switching
Cycle.
E
0
0
Rg – GATE RESISTANCE –
100
3
20
7
40
2
60
80
6
Qg = 100 nC
Qg = 250 nC
Qg = 500 nC
5
4
1
V
CC
= 19 V
V
EE
= -9 V
LED Drive Circuit
Considerations for Ultra
High CMR Performance
Without a detector shield, the
dominant cause of optocoupler
CMR failure is capacitive
coupling from the input side of
the optocoupler, through the
package, to the detector IC as
shown in Figure 29. The HCPL-
3150/315J improves CMR
performance by using a detector
IC with an optically transparent
Faraday shield, which diverts the
capacitively coupled current away
from the sensitive IC circuitry.
How ever, this shield does not
eliminate the capacitive coupling
between the LED and optocoup-
ler pins 5-8 as shown in
Figure 30. This capacitive
coupling causes perturbations in
the LED current during common
mode transients and becomes the
major source of CMR failures for
a shielded optocoupler. The main
design objective of a high CMR
LED drive circuit becomes
keeping the LED in the proper
state (on or off) during common
mode transients. For example,
the recommended application
circuit (Figure 25), can achieve
15 kV/
μ
s CMR while minimizing
component complexity.
Techniques to keep the LED in
the proper state are discussed in
the next two sections.
logic gate is less than V
F(OFF)
, the
LED will remain off and no
common mode failure will occur.
The open collector drive circuit,
shown in Figure 32, cannot keep
the LED off during a +dV
CM
/dt
transient, since all the current
flowing through C
LEDN
must be
supplied by the LED, and it is not
recommended for applications
requiring ultra high CMR
L
performance. Figure 33 is an
alternative drive circuit which,
like the recommended application
circuit (Figure 25), does achieve
ultra high CMR performance by
shunting the LED in the off state.
Under Voltage Lockout
Feature
The HCPL-3150/315J contains an
under voltage lockout (UVLO)
feature that is designed to protect
the IGBT under fault conditions
which cause the HCPL-3150/315J
supply voltage (equivalent to the
fully-charged IGBT gate voltage)
to drop below a level necessary to
keep the IGBT in a low resistance
state. When the HCPL-3150/315J
output is in the high state and the
supply voltage drops below the
HCPL-3150/315J V
UVLO-
threshold
(9.5 <V
UVLO-
<12.0), the
optocoupler output will go into
the low state with a typical delay,
UVLO Turn Off Delay, of 0.6
μ
s.
When the HCPL-3150/315J
output is in the low state and the
supply voltage rises above the
HCPL-3150/315J V
UVLO+
threshold (11.0 < V
UVLO+
< 13.5),
the optocoupler will go into the
相關PDF資料 |
PDF描述 |
|---|---|
| HCPL-316J | 2.0 Amp Gate Drive Optocoupler with Integrated (V CE ) Desaturation Detection and Fault Status Feedback(帶集成不飽和檢測和誤差反饋的2.0 Amp門驅動耦合器) |
| HCPL-3700 | AC/DC to Logic Interface Optocouplers(AC/DC邏輯接口光耦合器) |
| HCPL-4100300 | Optically Coupled 20 mA Current Loop Transmitter |
| HCPL-4100500 | Optically Coupled 20 mA Current Loop Transmitter |
| HCPL4100 | Optically Coupled 20 mA Current Loop Transmitter |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HCPL-315J#500 | 功能描述:邏輯輸出光電耦合器 0.5A IGBT Gate Drive RoHS:否 制造商:Fairchild Semiconductor 絕緣電壓:4243 Vrms 輸出類型:Push-Pull 最大傳播延遲時間:500 ns 最大正向二極管電壓: 最大反向二極管電壓: 最大正向二極管電流: 最大連續輸出電流:2.5 A 最大功率耗散:100 mW 最大工作溫度:+ 100 C 最小工作溫度:- 40 C 封裝 / 箱體:SO-16 封裝:Tube |
| HCPL-315J-000E | 功能描述:邏輯輸出光電耦合器 0.5A IGBT Gate Drive RoHS:否 制造商:Fairchild Semiconductor 絕緣電壓:4243 Vrms 輸出類型:Push-Pull 最大傳播延遲時間:500 ns 最大正向二極管電壓: 最大反向二極管電壓: 最大正向二極管電流: 最大連續輸出電流:2.5 A 最大功率耗散:100 mW 最大工作溫度:+ 100 C 最小工作溫度:- 40 C 封裝 / 箱體:SO-16 封裝:Tube |
| HCPL-315J-500E | 功能描述:邏輯輸出光電耦合器 0.5A IGBT Gate Drive RoHS:否 制造商:Fairchild Semiconductor 絕緣電壓:4243 Vrms 輸出類型:Push-Pull 最大傳播延遲時間:500 ns 最大正向二極管電壓: 最大反向二極管電壓: 最大正向二極管電流: 最大連續輸出電流:2.5 A 最大功率耗散:100 mW 最大工作溫度:+ 100 C 最小工作溫度:- 40 C 封裝 / 箱體:SO-16 封裝:Tube |
| HCPL-316J | 功能描述:邏輯輸出光電耦合器 2.0A IGBT Gate Drive RoHS:否 制造商:Fairchild Semiconductor 絕緣電壓:4243 Vrms 輸出類型:Push-Pull 最大傳播延遲時間:500 ns 最大正向二極管電壓: 最大反向二極管電壓: 最大正向二極管電流: 最大連續輸出電流:2.5 A 最大功率耗散:100 mW 最大工作溫度:+ 100 C 最小工作溫度:- 40 C 封裝 / 箱體:SO-16 封裝:Tube |
| HCPL-316J#500 | 功能描述:邏輯輸出光電耦合器 2.0A IGBT Gate Drive RoHS:否 制造商:Fairchild Semiconductor 絕緣電壓:4243 Vrms 輸出類型:Push-Pull 最大傳播延遲時間:500 ns 最大正向二極管電壓: 最大反向二極管電壓: 最大正向二極管電流: 最大連續輸出電流:2.5 A 最大功率耗散:100 mW 最大工作溫度:+ 100 C 最小工作溫度:- 40 C 封裝 / 箱體:SO-16 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。