參數資料
型號： HCPL-3150
英文描述： Single Channel 0.5 Amp Output Current IGBT Gate Drive Optocoupler(單通道 0.5 Amp輸出電流 IGBT門驅動耦合器)
中文描述： 單通道0.5安培的輸出電流IGBT柵極驅動光電耦合器（單通道0.5安培輸出電流IGBT的門驅動耦合器）
文件頁數： 8/20頁
文件大小： 320K
代理商： HCPL-3150
8
Notes:
1. Derate linearly above 70
°
C free-air
temperature at a rate of 0.3 mA/
°
C.
2. Maximum pulse width = 10
μ
s,
maximum duty cycle = 0.2%. This
value is intended to allow for
component tolerances for designs
with I
O
peak minimum = 0.5 A. See
Applications section for additional
details on limiting I
OH
peak.
3. Derate linearly above 70
°
C free-air
temperature at a rate of 4.8 mW/
°
C.
4. Derate linearly above 70
°
C free-air
temperature at a rate of 5.4 mW/
°
C.
The maximum LED junction tempera-
ture should not exceed 125
°
C.
5. Maximum pulse width = 50
μ
s,
maximum duty cycle = 0.5%.
6. In this test V
OH
is measured with a dc
load current. When driving capacitive
loads V
OH
will approach V
CC
as I
OH
approaches zero amps.
7. Maximum pulse width = 1 ms,
maximum duty cycle = 20%.
8. In accordance with UL1577, each
HCPL-3150 optocoupler is proof
tested by applying an insulation test
voltage
≥
3000 Vrms (
≥
5000 Vrms
for the HCPL-315J) for 1 second
(leakage detection current limit, I
I-O
≤
5
μ
A). This test is performed
before the 100% production test for
partial discharge (method b) shown
in the VDE 0884 Insulation
Characteristics Table, if applicable.
9. Device considered a two-terminal
device: pins on input side shorted
together and pins on output side
shorted together.
10. The difference between t
PHL
and t
PLH
between any two parts or channels
under the same test condition.
11. Pins 1 and 4 (HCPL-3150) and pins 3
and 4 (HCPL-315J) need to be
connected to LED common.
12. Common mode transient immunity in
the high state is the maximum
tolerable |dV
CM
/dt| of the common
mode pulse, V
CM
, to assure that the
output will remain in the high state
(i.e., V
O
> 15.0 V).
13. Common mode transient immunity in
a low state is the maximum tolerable
|dV
CM
/dt| of the common mode
pulse, V
CM
, to assure that the output
will remain in a low state (i.e.,
V
O
< 1.0 V).
14. This load condition approximates the
gate load of a 1200 V/25 A IGBT.
15. Pulse Width Distortion (PWD) is
defined as |t
PHL
-t
PLH
| for any given
device.
16. Each channel.
17. Device considered a two terminal
device: Channel one output side pins
shorted together, and channel two
output side pins shorted together.
18. See the thermal model for the
HCPL-315J in the application
section of this data sheet.
Package Characteristics
(each channel, unless otherwise specified)
Parameter
Symbol
Device
Input-Output
V
ISO
HCPL-3150
Momentary
Withstand Voltage**
HCPL-315J
Output-Output
V
O-O
HCPL-315J
Momentary
Withstand Voltage**
Resistance
R
I-O
(Input - Output)
Capacitance
C
I-O
HCPL-3150
(Input - Output)
HCPL-315J
LED-to-Case
θ
LC
HCPL-3150
Thermal Resistance
LED-to-Detector
θ
LD
HCPL-3150
Thermal Resistance
Detector-to-Case
θ
DC
HCPL-3150
Thermal Resistance
Min.
2500
Typ.*
Max. Units
Test Conditions
RH < 50%,
t = 1 min.,
T
A
= 25
°
C
RH < 50%
t = 1 min.,
T
A
= 25
°
C
V
I-O
= 500 V
DC
Fig.
Note
8, 9
Vrms
3750
1500
Vrms
17
10
12
9
0.6
1.3
391
pF
f = 1 MHz
°
C/W
Thermocouple
located at center
underside of
package
28
18
439
°
C/W
119
°
C/W
*All typical values at T
A
= 25
°
C and V
CC
- V
EE
= 30 V, unless otherwise noted.
**The Input-Output/Output-Output Momentary Withstand Voltage is a dielectric voltage rating that should not be interpreted as an input-
output/output-output continuous voltage rating. For the continuous voltage rating refer to your equipment level safety specification or Agilent
Application Note 1074 entitled “Optocoupler Input-Output Endurance Voltage.”
相關PDF資料
PDF描述
HCPL-315J Dual Channel 0.5 Amp Output Current IGBT Gate Drive Optocoupler(雙通道 0.5 Amp輸出電流 IGBT門驅動耦合器)
HCPL-316J 2.0 Amp Gate Drive Optocoupler with Integrated (V CE ) Desaturation Detection and Fault Status Feedback(帶集成不飽和檢測和誤差反饋的2.0 Amp門驅動耦合器)
HCPL-3700 AC/DC to Logic Interface Optocouplers(AC/DC邏輯接口光耦合器)
HCPL-4100300 Optically Coupled 20 mA Current Loop Transmitter
HCPL-4100500 Optically Coupled 20 mA Current Loop Transmitter
相關代理商/技術參數
參數描述
HCPL-3150#060 功能描述:邏輯輸出光電耦合器 0.5A IGBT Gate Drive RoHS:否 制造商:Fairchild Semiconductor 絕緣電壓:4243 Vrms 輸出類型:Push-Pull 最大傳播延遲時間:500 ns 最大正向二極管電壓: 最大反向二極管電壓: 最大正向二極管電流: 最大連續輸出電流:2.5 A 最大功率耗散:100 mW 最大工作溫度:+ 100 C 最小工作溫度:- 40 C 封裝 / 箱體:SO-16 封裝:Tube
HCPL-3150#300 功能描述:邏輯輸出光電耦合器 0.5A IGBT Gate Drive RoHS:否 制造商:Fairchild Semiconductor 絕緣電壓:4243 Vrms 輸出類型:Push-Pull 最大傳播延遲時間:500 ns 最大正向二極管電壓: 最大反向二極管電壓: 最大正向二極管電流: 最大連續輸出電流:2.5 A 最大功率耗散:100 mW 最大工作溫度:+ 100 C 最小工作溫度:- 40 C 封裝 / 箱體:SO-16 封裝:Tube
HCPL-3150#360 功能描述:邏輯輸出光電耦合器 0.5A IGBT Gate Drive RoHS:否 制造商:Fairchild Semiconductor 絕緣電壓:4243 Vrms 輸出類型:Push-Pull 最大傳播延遲時間:500 ns 最大正向二極管電壓: 最大反向二極管電壓: 最大正向二極管電流: 最大連續輸出電流:2.5 A 最大功率耗散:100 mW 最大工作溫度:+ 100 C 最小工作溫度:- 40 C 封裝 / 箱體:SO-16 封裝:Tube
HCPL-3150#500 功能描述:邏輯輸出光電耦合器 0.5A IGBT Gate Drive RoHS:否 制造商:Fairchild Semiconductor 絕緣電壓:4243 Vrms 輸出類型:Push-Pull 最大傳播延遲時間:500 ns 最大正向二極管電壓: 最大反向二極管電壓: 最大正向二極管電流: 最大連續輸出電流:2.5 A 最大功率耗散:100 mW 最大工作溫度:+ 100 C 最小工作溫度:- 40 C 封裝 / 箱體:SO-16 封裝:Tube
HCPL-3150#560 功能描述:邏輯輸出光電耦合器 0.5A IGBT Gate Drive RoHS:否 制造商:Fairchild Semiconductor 絕緣電壓:4243 Vrms 輸出類型:Push-Pull 最大傳播延遲時間:500 ns 最大正向二極管電壓: 最大反向二極管電壓: 最大正向二極管電流: 最大連續輸出電流:2.5 A 最大功率耗散:100 mW 最大工作溫度:+ 100 C 最小工作溫度:- 40 C 封裝 / 箱體:SO-16 封裝:Tube
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*