- 您現在的位置：買賣IC網 > PDF目錄370450 > HCPL-2530 Dual Channel, High Speed Optocouplers(雙通道，高速光耦合器) PDF資料下載
參數資料
| 型號： | HCPL-2530 |
| 英文描述： | Dual Channel, High Speed Optocouplers(雙通道，高速光耦合器) |
| 中文描述： | 雙通道，高速光電耦合器（雙通道，高速光耦合器） |
| 文件頁數： | 9/12頁 |
| 文件大小： | 221K |
| 代理商： | HCPL-2530 |
9
Notes:
1. Each channel.
2. CURRENT TRANSFER RATIO is
defined as the ratio of output
collector current, I
O
, to the forward
LED input current, I
F
, times 100%.
3. Device considered a two-terminal
device: pins 1, 2, 3, and 4 shorted
together and pins 5, 6, 7, and 8
shorted together.
4. Measured between pins 1 and 2
shorted together, and pins 3 and 4
shorted together.
5. Common mode transient immunity in
a Logic High level is the maximum
tolerable (positive) dV
CM
/dt on the
rising edge of the common mode
pulse, V
CM
, to assure that the output
will remain in a Logic High state (i.e.,
V
O
> 2.0 V). Common mode transient
immunity in a Logic Low level is the
maximum tolerable (negative)
dV
CM
/dt on the falling edge of the
common mode pulse signal, V
CM
, to
assure that the output will remain in a
Logic Low state (i.e., V
O
< 0.8 V).
6. The 1.9 k
load represents 1 TTL
unit load of 1.6 mA and the 5.6 k
pull-up resistor.
7. The 4.1 k
load represents 1 LSTTL
unit load of 0.36 mA and the 6.1 k
pull-up resistor.
8. The frequency at which the ac output
voltage is 3 dB below the low
frequency asymptote.
9. Use of a 0.1
μ
F bypass capacitor
connected between pins 5 and 8 is
recommended.
10. In accordance with UL 1577, each
optocoupler is proof tested by
applying an insulation test voltage
≥
3000 V rms for 1 second (leakage
detection current limit, I
I-O
≤
5
μ
A).
11. In accordance with UL 1577, each
optocoupler is proof tested by
applying an insulation test voltage
≥
6000 V rms for 1 second (leakage
detection current limit, I
I-O
≤
5
μ
A).
12. Measured between the LED anode and
cathode shorted together and pins 5
through 8 shorted together.
13. Derate linearly above 90
°
C free-air
temperature at a rate of 3.0 mW/
°
C
for the SOIC-8 package.
Figure 1. DC and Pulsed Transfer
Characteristics.
Figure 2. Current Transfer Ratio vs.
Input Current.
Figure 3. Input Current vs. Forward
Voltage.
0
10
20
V
O
– OUTPUT VOLTAGE – V
I
O
10
5
0
T = 25°C
V = 5.0 V
40 mA
35 mA
30 mA
25 mA
20 mA
15 mA
10 mA
I = 5 mA
NORMALIZED
I = 16 mA
V = 0.5 V
V = 5 V
T = 25°C
10
HCPL-2530/0530
HCPL-2531/0531/4534/0534
1.5
1.0
0.5
0.1
0
1
100
N
I
F
– INPUT CURRENT – mA
V
F
– FORWARD VOLTAGE – VOLTS
100
10
0.1
0.01
1.1
1.2
1.3
1.4
I
F
1.6
1.5
1.0
0.001
1000
I
F
V
F
–
+
T = 25°C
相關PDF資料 |
PDF描述 |
|---|---|
| HCPL-2531 | Dual Channel, High Speed Optocouplers(雙通道，高速光耦合器) |
| HCPL-2602 | High CMR Line Receiver Optocouplers(高共態抑制線接收光耦器) |
| HCPL-261A | HCMOS Compatible, High CMR, 10 MBd Optocouplers |
| HCPL-261N | High CMR, High Speed TTL Compatible Optocouplers |
| HCPL-2630 | High CMR, High Speed TTL Compatible Optocouplers |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HCPL2530#020 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:NPN-OUTPUT DC-INPUT OPTOCOUPLER |
| HCPL-2530#020 | 功能描述:高速光耦合器 1MBd 2Ch 16mA RoHS:否 制造商:Avago Technologies 電流傳遞比: 最大波特率: 最大正向二極管電壓:1.75 V 最大反向二極管電壓:5 V 最大功率耗散:40 mW 最大工作溫度:+125 C 最小工作溫度:- 40 C 封裝 / 箱體:SOIC-5 封裝:Tube |
| HCPL2530#300 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:NPN-OUTPUT DC-INPUT OPTOCOUPLER |
| HCPL-2530#300 | 功能描述:高速光耦合器 1MBd 2Ch 16mA RoHS:否 制造商:Avago Technologies 電流傳遞比: 最大波特率: 最大正向二極管電壓:1.75 V 最大反向二極管電壓:5 V 最大功率耗散:40 mW 最大工作溫度:+125 C 最小工作溫度:- 40 C 封裝 / 箱體:SOIC-5 封裝:Tube |
| HCPL-2530#320 | 功能描述:高速光耦合器 1MBd 2Ch 16mA RoHS:否 制造商:Avago Technologies 電流傳遞比: 最大波特率: 最大正向二極管電壓:1.75 V 最大反向二極管電壓:5 V 最大功率耗散:40 mW 最大工作溫度:+125 C 最小工作溫度:- 40 C 封裝 / 箱體:SOIC-5 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。