- 您現在的位置：買賣IC網 > PDF目錄370450 > HCPL-0560 Dual Channel Bi-directional High Speed Optoisolators(雙通道雙向高速光隔離器) PDF資料下載
參數資料
| 型號： | HCPL-0560 |
| 英文描述： | Dual Channel Bi-directional High Speed Optoisolators(雙通道雙向高速光隔離器) |
| 中文描述： | 雙通道雙向高速光隔離器（雙通道雙向高速光隔離器） |
| 文件頁數： | 7/16頁 |
| 文件大?。?/td> | 258K |
| 代理商： | HCPL-0560 |
7
Package Characteristics
All typical values at T
A
= 25C.
Parameter
Side 1 – Side 2
Momentary Withstand
Voltage*
Side 1 – Side 2
Resistance
Side 1 – Side 2
Capacitance
Sym.
V
ISO
Min. Typ. Max. Units Test Conditions
2500
Vrms
Fig. Note
RH < 50%, t = 1 min.,
T
A
= 25
°
C
9,10
R
1–2
10
12
RH
≤
45%, t = 5
S
,
V
I–O
= 500 Vdc
f = 1 MHz
9
C
1–2
0.25
pF
9
* The Input–Output Momentary Withstand Voltage is a dielectric voltage rating that should not be interpreted as an input-output
continuous voltage rating. For the continuous voltage rating refer to the VDE 0884 Insulation Characteristics Table (if applicable),
your equipment level safety specification or Agilent Application Note 1074 entitled “Optocoupler Input–Output Endurance Voltage,”
publication number 5963-2203E.
Notes:
1. Derate linearly above 90C free-air temperature at a rate of 3.0 mW/C.
2. In the V
CC
common configuration, Input LED current is a function of the V
CC
supply voltage. See application information section
to set the proper drive currents.
3. Each channel.
4. DC CURRENT TRANSFER RATIO is defined as the ratio of output collector current, I
O
, to the forward LED input current I
F
,
times 100%.
5. The 1.9 k
load represents 1 TTL load of 1.6 mA and 5.6 k
pull-up resistor.
6. Use of a 0.1
μ
F bypass capacitor connected between pins 1 and 3, & 5 and 7 adjacent to the device is recommended.
7. Common mode transient immunity in a Logic High level is the maximum tolerable (positive) dV
CM
/dt of the common mode pulse,
V
CM,
to assure that the output will remain in a Logic High state (i.e., V
O
> 2.0 V).
Common mode transient immunity in a Logic Low level is the maximum tolerable (negative) dV
CM
/dt of the common mode pulse,
V
CM,
to assure that the output will remain in a Logic Low state (i.e., V
O
< 0.8 V).
8. The frequency at which the ac output voltage of 3 dB below the low frequency asymptote.
9. Device considered a two-terminal device. Pins 1, 2, 3, and 4 shorted together and Pins 5, 6, 7, and 8 shorted together.
10. In accordance with UL 1577, each optocoupler is proof tested by applying an insulation test voltage 3000 Vrms for 1 second
(leakage detection current limit, I
I–O
< 5
μ
A).
-
相關PDF資料 |
PDF描述 |
|---|---|
| HCPL-0561 | Dual Channel Bi-directional High Speed Optoisolators(雙通道雙向高速光隔離器) |
| HCPL-0601 | High CMR, High Speed TTL Compatible Optocouplers(高CMR，高速TTL兼容光耦合器) |
| HCPL-0661 | High CMR, High Speed TTL Compatible Optocouplers(高CMR，高速TTL兼容光耦合器) |
| HCNW137 | High CMR, High Speed TTL Compatible Optocouplers(高CMR，高速TTL兼容光耦合器) |
| HCPL-2601 | High CMR, High Speed TTL Compatible Optocouplers(高CMR，高速TTL兼容光耦合器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HCPL-0560500 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:NPN-OUTPUT DC-INPUT OPTOCOUPLER |
| HCPL-0560E | 制造商:AVAGO 制造商全稱:AVAGO TECHNOLOGIES LIMITED 功能描述:Intelligent Power Module and Gate Drive Interface Optocouplers |
| HCPL-0561 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:NPN-OUTPUT DC-INPUT OPTOCOUPLER |
| HCPL-0561500 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:NPN-OUTPUT DC-INPUT OPTOCOUPLER |
| HCPL0600 | 功能描述:高速光耦合器 10MBit Optocoupler HS Logic Gate RoHS:否 制造商:Avago Technologies 電流傳遞比: 最大波特率: 最大正向二極管電壓:1.75 V 最大反向二極管電壓:5 V 最大功率耗散:40 mW 最大工作溫度:+125 C 最小工作溫度:- 40 C 封裝 / 箱體:SOIC-5 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。