參數資料
型號： HCD66727A04
廠商： Hitachi,Ltd.
英文描述： Low-Power Dot-Matrix Liquid Crystal Display Controller/Driver with Key Scan Function
中文描述： 低功耗點陣液晶顯示控制器/鍵掃描功能驅動程序
文件頁數： 86/97頁
文件大?。?/td> 513K
代理商： HCD66727A04
HD66727
86
Standby Mode
Setting the standby mode bit (STB) to 1 puts the HD66727 in the standby mode, where the device stops
completely, halting all internal operations including the R-C oscillator, thus further reducing current
consumption compared to that in the sleep mode. Specifically, character and segment displays, which are
controlled by the multiplexing drive method, are completely halted. Here, all the SEG (SEG1 to SEG60)
and COM (COM1 to COM34) pins output the V
CC
level, resulting in no display. If the AMP bit is set to 0
in the standby mode, the LCD drive power supply can be turned off.
Annunciators can be displayed simply by supplying an approximately 40-Hz alternating signal for the LCD
drive signals to the EXM pin externally. If annunciator display is unnecessary during the standby mode, the
EXM pin must be fixed to the V
CC
or GND level and the annunciator display on bit (DA) set to 0.
During the standby mode, no instructions can be accepted other than those for annunciator display, the
start-oscillator instruction, and the key scan interrupt generation enable instruction. To cancel the standby
mode, issue the start oscillator instruction to stabilize R-C oscillation before setting the STB bit to 0.
Although key scan is halted in the standby mode, the HD66727 can detect four key inputs connected with
strobe signal KST0, thus generating the key scan interrupt (IRQ*). This means, the system can be activated
from the completely inactive state. For details, refer to the Key Scan Control section.
Figure 50 shows the procedure for setting and canceling the standby mode.
Turn off the LCD power supply: AMP = 0
Only for annunciator display;
set the DA bit to 0 when
annunciator display is not necessary.
Set standby mode: STB = 1
Supply an external alternating signal to the EXM pin
Issue the start-oscillator instruction
Wait at least 10 ms
Cancel standby mode: STB = 0
Turn on the LCD drive power supply: AMP = 1
Standby mode (only annunciator display is available)
Figure 50 Procedure for Setting and Canceling Standby Mode
相關PDF資料
PDF描述
HCD66727A04BP Low-Power Dot-Matrix Liquid Crystal Display Controller/Driver with Key Scan Function
HCD66730A00 Dot-Matrix Liquid Crystal Display Controller/Driver Supporting Japanese Kanji, Korean Font Display
HCD66730A01 Dot-Matrix Liquid Crystal Display Controller/Driver Supporting Japanese Kanji, Korean Font Display
HCD66731A00BP Dot-Matrix Liquid Crystal Display Controller/Driver Supporting Japanese Kanji, Korean Font Display
HCD66731A01BP Dot-Matrix Liquid Crystal Display Controller/Driver Supporting Japanese Kanji, Korean Font Display
相關代理商/技術參數
參數描述
HCD66727A04BP 制造商:HITACHI 制造商全稱:Hitachi Semiconductor 功能描述:Low-Power Dot-Matrix Liquid Crystal Display Controller/Driver with Key Scan Function
HCD66730A00 制造商:HITACHI 制造商全稱:Hitachi Semiconductor 功能描述:Dot-Matrix Liquid Crystal Display Controller/Driver Supporting Japanese Kanji, Korean Font Display
HCD66730A01 制造商:HITACHI 制造商全稱:Hitachi Semiconductor 功能描述:Dot-Matrix Liquid Crystal Display Controller/Driver Supporting Japanese Kanji, Korean Font Display
HCD66731A00BP 制造商:HITACHI 制造商全稱:Hitachi Semiconductor 功能描述:Dot-Matrix Liquid Crystal Display Controller/Driver Supporting Japanese Kanji, Korean Font Display
HCD66731A01BP 制造商:HITACHI 制造商全稱:Hitachi Semiconductor 功能描述:Dot-Matrix Liquid Crystal Display Controller/Driver Supporting Japanese Kanji, Korean Font Display
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*