- 您現在的位置：買賣IC網 > PDF目錄370424 > HAL501E (Electronic Theatre Controls, Inc.) JT 6C 6#22D SKT RECP PDF資料下載
參數資料
| 型號： | HAL501E |
| 廠商： | Electronic Theatre Controls, Inc. |
| 英文描述： | JT 6C 6#22D SKT RECP |
| 中文描述： | 霍爾效應傳感器系列 |
| 文件頁數： | 40/44頁 |
| 文件大?。?/td> | 315K |
| 代理商： | HAL501E |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁當前第40頁第41頁第42頁第43頁第44頁
HAL5xx
40
Micronas
5. Application Notes
5.1. Ambient Temperature
Due to the internal power dissipation, the temperature
on the silicon chip (junction temperature T
J
) is higher
than the temperature outside the package (ambient tem-
perature T
A
).
T
J
= T
A
+
T
At static conditions, the following equation is valid:
T = I
DD
* V
DD
* R
th
For typical values, use the typical parameters. For worst
case calculation, use the max. parameters for I
DD
and
R
th
, and the max. value for V
DD
from the application.
For all sensors, the junction temperature range T
J
is
specified. The maximum ambient temperature T
Amax
can be calculated as:
T
Amax
= T
Jmax
–
T
5.2. Extended Operating Conditions
All sensors fulfill the electrical and magnetic characteris-
tics when operated within the Recommended Operating
Conditions (see page 7).
Supply Voltage Below 3.8 V
Typically, the sensors operate with supply voltages
above 3 V, however, below 3.8 V some characteristics
may be outside the specification.
Note:
The functionality of the sensor below 3.8 V has not
been tested. For special test conditions, please contact
Micronas.
5.3. Start-up Behavior
Due to the active offset compensation, the sensors have
an initialization time (enable time t
en(O)
) after applying
the supply voltage. The parameter t
en(O)
is specified in
the Electrical Characteristics (see page 8).
During the initialization time, the output state is not de-
fined and the output can toggle. After t
en(O)
, the output
will be low if the applied magnetic field B is above B
ON
.
The output will be high if B is below B
OFF
. In case of sen-
sors with an inverted switching behavior (HAL516 ...
HAL519), the output state will be high if B > B
OFF
and low
if B < B
ON
.
For magnetic fields between B
OFF
and B
ON
, the output
state of the HAL sensor after applying V
DD
will be either
low or high. In order to achieve a well-defined output
state, the applied magnetic field must be above B
ONmax
,
respectively, below B
OFFmin
.
5.4. EMC and ESD
For applications with disturbances on the supply line or
radiated disturbances, a series resistor and a capacitor
are recommended (see figures 5
–
1). The series resistor
and the capacitor should be placed as closely as pos-
sible to the HAL sensor.
Applications with this arrangement passed the EMC
tests according to the product standards DIN 40839.
Note:
The international standard ISO 7637 is similar to
the used product standard DIN 40839.
Please contact Micronas for the detailed investigation
reports with the EMC and ESD results.
OUT
GND
3
2
1
V
DD
4.7 nF
V
EMC
V
P
R
V
220
R
L
1.2 k
20 pF
Fig. 5
–
1:
Test circuit for EMC investigations
相關PDF資料 |
PDF描述 |
|---|---|
| HAL501K | JT 6C 6#22M PIN RECP |
| HAL502 | Circular Connector; No. of Contacts:6; Series:MS27497; Body Material:Aluminum; Connecting Termination:Crimp; Connector Shell Size:8; Circular Contact Gender:Pin; Circular Shell Style:Wall Mount Receptacle; Insert Arrangement:8-35 RoHS Compliant: No |
| HAL525UA-K | Hall Effect Sensor IC |
| HAL535SF-A | Hall Effect Sensor IC |
| HAL535SF-E | Hall Effect Sensor IC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HAL501K | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Hall Effect Sensor Family |
| HAL501S-A | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Hall-Effect Switch |
| HAL501S-C | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Hall-Effect Switch |
| HAL501S-E | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Hall-Effect Switch |
| HAL501SF-A | 制造商:MICRONAS 制造商全稱:MICRONAS 功能描述:Hall-Effect Sensor Family |
發布緊急采購，3分鐘左右您將得到回復。