- 您現在的位置：買賣IC網 > PDF目錄385353 > HA457CM (INTERSIL CORP) 95MHz, Low Power, AV = 2, 8 x 8 Video Crosspoint Switch PDF資料下載
參數資料
| 型號： | HA457CM |
| 廠商： | INTERSIL CORP |
| 元件分類： | 運動控制電子 |
| 英文描述： | 95MHz, Low Power, AV = 2, 8 x 8 Video Crosspoint Switch |
| 中文描述： | 8-CHANNEL, CROSS POINT SWITCH, PQCC44 |
| 封裝： | PLASTIC, MS-018AC, LCC-44 |
| 文件頁數： | 8/14頁 |
| 文件大?。?/td> | 175K |
| 代理商： | HA457CM |
8
32-Bit Serial Mode
In the serial programming mode, all master registers are
loaded with data, making it unnecessary to specify an output
address (A2:0). The input data format is D3-D0, starting with
OUT0 and ending with OUT7 for 32 total bits (i.e., first bit
shifted in is D3 for OUT0, and 32nd bit shifted in is D0 for
OUT7). Only codes 0000 through 1010 are valid serial mode
commands. Code 1010 disables an individual output, while
code 1001 enables it. After data is shifted into the 32-bit
Master Register, it transfers to the Slave Register on the
rising edge of the LATCH line (Edge mode), or when
LATCH = 0 (Level mode, see Figure 10).
Figure 6 shows a typical application of the HA457 for driving
75
loads. This application shows the HA457 digital-switch
control interface set up in the 7-bit parallel mode. The HA457
uses 7 data lines and 3 control lines (WR, CE and LATCH).
The input/output information is presented to the chip at A2:0
and D3:0 by a parallel printer port. The data is stored in the
master registers on the rising edge of WR. When the LATCH
line goes high, the switch configuration loads into the slave
registers, and all 8 outputs reconfigure at the same time.
Each 7-bit word updates only one output at a time. If several
outputs are to be updated, the data is individually loaded into
the master registers. Then, a single LATCH pulse can
reconfigure all channels simultaneously.
An IBM compatible PC loads the programming data into the
HA457 via its parallel port (LPT1) using a simple BASIC
program.
TABLE 1. PARALLEL INTERFACE COMMANDS
A2:0
D3:0
ACTION
Selects
Output
Being
Programmed
0000 to 0111
Connect the input defined by D3:0 to the output selected by A2:0. Doesn’t enable a disabled output.
1000
Connect the output selected by A2:0 to GND. Doesn’t enable a disabled output.
1011
Asynchronously disable the single output selected by A2:0, and leave the Master Register unchanged.
1100
Asynchronously enable the single output selected by A2:0, and leave the Master Register unchanged.
Address
Inputs are
Irrelevant for
These
Functions
1101
Asynchronously disable all outputs, and leave the Master Register unchanged.
1110
Asynchronously enable all outputs, and leave the Master Register unchanged.
1111
Send a Software pulse to the Slave Register to load it from the Master Register, iff, the LATCH input=1. If the
LATCH input=0, then this command is a NOP. The Master Register is unchanged by this command.
1001 or 1010
Do not use these codes in the parallel programming mode. These codes are for serial programming only.
TABLE 2. SERIAL INTERFACE COMMANDS
D3:0
ACTION
0000 to 0111
Connect the output to the input channel defined by D3:0. Doesn’t enable a disabled output.
1000
Connect the output to GND. Doesn’t enable a disabled output.
1001
Enable the output and connect it to GND. The default power-up state is all outputs disabled, so use this code to enable
outputs after power is applied, but before programming the switch configuration.
1010
Disable the output. The output is no longer associated with any input channel; the desired input must be redefined after
reenabling the output.
1011 to 1111
Do not use these codes in the serial programming mode.
TABLE 3. DEFINITION OF DATA AND ADDRESS BIT FUNCTIONS
SER/PAR
D3
D2
D1
D0
A2:0
COMMENT
H
X
X
Serial
Data
Output
Serial
Data
Input
X
32-Bit Serial Mode
L
H
Parallel Data
Input
Parallel Data
Input
Parallel Data
Input
Output
Address
Parallel Mode; D2:0 define the
command to be executed.
L
L
Parallel Data
Input
Parallel Data
Input
Parallel Data
Input
Output
Address
Parallel Mode; D2:0 define the
Input Channel
HA457
相關PDF資料 |
PDF描述 |
|---|---|
| HA457CN | 95MHz, Low Power, AV = 2, 8 x 8 Video Crosspoint Switch |
| HA457 | 95MHz, Low Power, AV = 2, 8 x 8 Video Crosspoint Switch |
| HA4905 | () |
| HA5013 | Triple, 125MHz Video Amplifier |
| HA5013IP | Triple, 125MHz Video Amplifier |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HA457CN | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| HA-460 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:CRYSTAL CLOCK OSCILLATORS |
| HA4600 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:480MHz, SOT-23, Video Buffer with Output Disable |
| HA4600_05 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:480MHz, SOT-23, Video Buffer with Output Disable |
| HA4600CB | 功能描述:IC VIDEO BUFFER 480MHZ 8-SOIC RoHS:否 類別:集成電路 (IC) >> 線性 - 放大器 - 視頻放大器和頻緩沖器 系列:- 標準包裝:1,000 系列:- 應用:驅動器 輸出類型:差分 電路數:3 -3db帶寬:350MHz 轉換速率:1000 V/µs 電流 - 電源:14.5mA 電流 - 輸出 / 通道:60mA 電壓 - 電源，單路/雙路(±):5 V ~ 12 V，±2.5 V ~ 6 V 安裝類型:表面貼裝 封裝/外殼:20-VFQFN 裸露焊盤 供應商設備封裝:20-QFN 裸露焊盤（4x4） 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。