2
Absolute Maximum Ratings
Thermal Information
Supply Voltage (Between V+ and V- Terminals) . . . . . . . . . . . . .35V
Differential Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6V
Output Current. . . . . . . . . . . . . . . . 50mA Continuous, 125mA
PEAK
Operating Conditions
Temperature Range
HA-2542-5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0
o
C to 75
o
C
Thermal Resistance (Typical, Note 2)
CERDIP Package. . . . . . . . . . . . . . . . .
PDIP Package . . . . . . . . . . . . . . . . . . .
Maximum Junction Temperature (Note 1, Hermetic Packages) . 175
o
C
Maximum Junction Temperature (Plastic Package) . . . . . . . .150
o
C
Maximum Storage Temperature Range. . . . . . . . . . -65
o
C to 150
o
C
Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . .300
o
C
θ
JA
(
o
C/W)
75
95
θ
JC
(
o
C/W)
20
N/A
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the
device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
NOTES:
1. Maximum power dissipation with load conditions must be designed to maintain the maximum junction temperature below 175
o
C for ceramic
packages, and below 150
o
C for plastic packages. By using Application Note AN556 on Safe Operating Area equations, along with the thermal
resistances, proper load conditions can be determined. Heatsinking will be required in many applications. See the “Application Information”
section to determine if heat sinking is required for your application.
2.
θ
JA
is measured with the component mounted on an evaluation PC board in free air.
Electrical Specifications
V
SUPPLY
=
±
15V, R
L
= 1k
,
C
L
≤
10pF, Unless Otherwise Specified
PARAMETER
TEST
CONDITIONS
TEMP.
(
o
C)
HA-2542-5
0
o
C TO 75
o
C
UNITS
MIN
TYP
MAX
INPUT CHARACTERISTICS
Offset Voltage
25
-
5
10
mV
Full
-
8
20
mV
Average Offset Voltage Drift
Full
-
14
-
μ
V/
o
C
Bias Current
25
-
15
35
μ
A
Full
-
26
50
μ
A
Average Bias Current Drift
Full
-
45
-
nA/
o
C
Offset Current
25
-
1
7
μ
A
Full
-
-
9
μ
A
Input Resistance
25
-
100
-
k
Input Capacitance
25
-
1
-
pF
Common Mode Range
Full
±
10
-
-
V
Input Noise Voltage
0.1Hz to 100Hz
25
-
2.2
-
μ
V
P-P
Input Noise Density
f = 1kHz, R
G
= 0
25
-
10
-
nV/
√
Hz
Input Noise Current Density
f = 1kHz, R
G
= 0
25
-
3
-
pA/
√
Hz
TRANSFER CHARACTERISTICS
Large Signal Voltage Gain
V
O
=
±
10V
25
10
30
-
kV/V
Full
5
20
-
kV/V
Common Mode Rejection Ratio
V
CM
=
±
10V
Full
70
100
-
dB
Minimum Stable Gain
25
2
-
-
V/V
Gain Bandwidth Product
A
V
= 100
25
-
70
-
MHz
OUTPUT CHARACTERISTICS
Output Voltage Swing
Full
±
10
±
11
-
V
Output Current (Note 3)
25
100
-
-
mA
Output Resistance
25
-
5
-
HA-2542