參數資料
型號： HA17385HRP
廠商： Hitachi,Ltd.
元件分類： 基準電壓源/電流源
英文描述： High Speed Current Mode PWM Control IC for Switching Power Supply(開關電源的高速電流模式PWM控制芯片)
中文描述： 高速開關電源電流模式PWM控制IC（開關電源的高速電流模式的PWM控制芯片）
文件頁數： 12/31頁
文件大小： 145K
代理商： HA17385HRP
HA17384SPS/SRP, HA17384HPS/HRP, HA17385HPS/HRP
12
Operation
(Description of Timing Chart)
From Power ON to Turn On
After the power is switched ON, the power supply terminal voltage (V
IN
) of this IC rises by charging
through bleeder resistor R
B
. At this time, when the power voltage is in the range of 2 V to 16 V*
1
. The
low-voltage, lock out UVL1 operates and accordingly the OUT voltage, that is, the gate voltage of the
power MOSFET, is fixed at 1.3 V or a lower value, resulting in the power MOSFET remaining in the OFF
state.
When the power supply voltage reaches 16 V, UVL1 of this IC is reset and the reference voltage (Vref)
generating part turns ON. However, until Vref becomes 4.7 V, the low-voltage, lock out UVL2 operates to
keep the OUT terminal voltage low. After Vref terminal voltage becomes 4.7 V or higher, OUT terminal
outputs a PWM pulse.
Note: 1. The value is for the HA17384S/H.
The value is 8.4 V for the HA17385H.
Generation of Triangular Wave and PWM Pulse
After the output of the Vref, each blocks begins to operate. The triangular wave is generated on the R
T
/C
T
terminal. For PWM pulses, the triangular wave rise time is taken as the variable on-duty on-time. The
triangular wave fall time is taken as the dead-band time. The initial rise of the triangular wave starts from 0
V, and to prevent a large on-duty at this time, the initial PWM pulse is masked and not output. PWM
pulses are outputted after the second triangular wave. The above operation is enabled by the charge energy
which is charged through the bleeder resistor R
B
into the capacitor C
B
of V
IN
.
Stationary Operation
PWM pulses are outputted after the second wave of the triangular wave and stationary operation as the
switching power supply starts.
By switching operation from ON/OFF to OFF/ON in the switching device (power MOSFET), the
transformer converts the voltage. The power supply of IC V
IN
is fed by the back-up winding of the
transformer.
In the current mode of the IC, the current in the switcing device is always monitored by a source resistor
R
CS
. Then the current limiter level is varied according to the error voltage (COMP terminal voltage) for
PWM control. One third of the error voltage level, which is divided by resistors “2R” and “R” in the IC, is
used to sense the current (R = 25 k
).
Two diodes between the error output and the 2R-R circuit act only as a DC level shifter. Actually, these
diodes are connected between the 2R-R circuit and GND, and, the current sensing comparator and GND,
respectively. Therefore, these blocks operate 1.4 V higher than the GND level. Accordingly, the error of the
current sensing level caused by the switching noise on the GND voltage level is eliminated. The zener
diode of 1 V symbolically indicates that the maximum sensing voltage level of the CS terminal is 1 V.
相關PDF資料
PDF描述
HA17384HRP High Speed Current Mode PWM Control IC for Switching Power Supply
HA17384SRP High Speed Current Mode PWM Control IC for Switching Power Supply
HA17385HPS High Speed Current Mode PWM Control IC for Switching Power Supply
HA17384 250000 SYSTEM GATE 1.5 VOLT FPGA
HA17393 Dual Comparator
相關代理商/技術參數
參數描述
HA17385HRP(E) 制造商:Renesas Electronics Corporation 功能描述:
HA17385PS 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Current-Mode SMPS Controller
HA17393 制造商:Panasonic Industrial Company 功能描述:I.C.
HA17393/ASERIES 制造商:未知廠家 制造商全稱:未知廠家 功能描述:
HA17393A 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:Dual Comparators
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*