- 您現在的位置：買賣IC網 > PDF目錄385347 > H1100I (Intersil Corporation) 850MHz, Low Distortion Current Feedback Operational Amplifiers PDF資料下載
參數資料
| 型號： | H1100I |
| 廠商： | Intersil Corporation |
| 元件分類： | 運動控制電子 |
| 英文描述： | 850MHz, Low Distortion Current Feedback Operational Amplifiers |
| 中文描述： | 是850MHz，低失真電流反饋運算放大器 |
| 文件頁數： | 4/10頁 |
| 文件大小： | 286K |
| 代理商： | H1100I |
4
FN2945.9
Application Information
Optimum Feedback Resistor (R
F
)
The enclosed plots of inverting and non-inverting frequency
response detail the performance of the HFA1100 in various
gains. Although the bandwidth dependency on A
CL
isn’t as
severe as that of a voltage feedback amplifier, there is an
appreciable decrease in bandwidth at higher gains. This
decrease can be minimized by taking advantage of the
current feedback amplifier’s unique relationship between
bandwidth and R
F
. All current feedback amplifiers require a
feedback resistor, even for unity gain applications, and the
R
F
, in conjunction with the internal compensation capacitor,
sets the dominant pole of the frequency response. Thus, the
amplifier’s bandwidth is inversely proportional to R
F
. The
HFA1100 design is optimized for a 510
R
F
, at a gain of +1.
Decreasing R
F
in a unity gain application decreases stability,
resulting in excessive peaking and overshoot (Note:
Capacitive feedback causes the same problems due to the
feedback impedance decrease at higher frequencies). At
higher gains the amplifier is more stable, so R
F
can be
decreased in a trade-off of stability for bandwidth. The table
below lists recommended R
F
values for various gains, and the
expected bandwidth.
5V Single Supply Operation
This amplifier operates at single supply voltages down to
4.5V. The table below details the amplifier’s performance
with a single 5V supply. The dramatic supply current
reduction at this operating condition (refer also to Figure 23)
makes these op amps even better choices for low power 5V
systems. Refer to Application Note AN9745 for further
information.
Use of Die in Hybrid Applications
This amplifier is designed with compensation to negate the
package parasitics that typically lead to instabilities. As a
result, the use of die in hybrid applications results in
overcompensated performance due to lower parasitic
capacitances. Reducing R
F
below the recommended values
for packaged units will solve the problem. For A
V
= +2 the
recommended starting point is 300
, while unity gain
applications should try 400
.
PC Board Layout
The frequency performance of this amplifier depends a great
deal on the amount of care taken in designing the PC board.
The use of low inductance components such as chip
resistors and chip capacitors is strongly recommended,
while a solid ground plane is a must!
Attention should be given to decoupling the power supplies.
A large value (10
μ
F) tantalum in parallel with a small value
chip (0.1
μ
F) capacitor works well in most cases.
Terminated microstrip signal lines are recommended at the
input and output of the device. Output capacitance, such as
that resulting from an improperly terminated transmission
line will degrade the frequency response of the amplifier and
may cause oscillations. In most cases, the oscillation can be
avoided by placing a resistor in series with the output.
Care must also be taken to minimize the capacitance to ground
seen by the amplifier’s inverting input. The larger this
capacitance, the worse the gain peaking, resulting in pulse
overshoot and possible instability. To this end, it is
recommended that the ground plane be removed under traces
connected to pin 2, and connections to pin 2 should be kept as
short as possible.
An example of a good high frequency layout is the
Evaluation Board shown below.
Evaluation Board
An evaluation board is available for the HFA1100 (Part
Number HFA11XXEVAL). Please contact your local sales
office for information.
A
CL
R
F
(
)
BW (MHz)
+1
510
850
-1
430
580
+2
360
670
+5
150
520
+10
180
240
+19
270
125
PARAMETER
TYP
Input Common Mode Range
1V to 4V
-3dB BW (A
V
= +2)
267MHz
Gain Flatness (to 50MHz, A
V
= +2)
0.05dB
Output Voltage (A
V
= -1)
1.3V to 3.8V
Slew Rate (A
V
= +2)
475V/
μ
s
0.1% Settling Time
17ns
Supply Current
5.5mA
HFA1100
相關PDF資料 |
PDF描述 |
|---|---|
| H1106I | 315MHz, Low Power, Video Operational Amplifier with Compensation Pin |
| H1114I | 850MHz Video Cable Driving Buffer |
| H11A1X | OPTICALLY COUPLED ISOLATOR PHOTOTRANSISTOR OUTPUT |
| H11A2X | OPTICALLY COUPLED ISOLATOR PHOTOTRANSISTOR OUTPUT |
| H11A3X | OPTICALLY COUPLED ISOLATOR PHOTOTRANSISTOR OUTPUT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| H1100NL | 功能描述:變壓器音頻和信號 TRANSFORMER RoHS:否 制造商:Skyworks Solutions, Inc. 頻率范圍:810 MHz to 960 MHz 初級線圈阻抗: 次級線圈阻抗: 絕緣電壓:23 dB 工作溫度范圍:- 40 C to + 85 C 端接類型:SMD/SMT 尺寸:6 mm L x 4.9 mm W x 1.6 mm H 產品:Splitters and Combiners |
| H1100T | 制造商:Pulse 功能描述:TRANSFORMER(SINGLE2:1) - Tape and Reel 制造商:Pulse Electronics Corporation 功能描述:Telecom Transformer 2:1/1:1 1500Vrms -1.1dB Surface Mount |
| H1101 | 功能描述:變壓器音頻和信號 XFMR RoHS:否 制造商:Skyworks Solutions, Inc. 頻率范圍:810 MHz to 960 MHz 初級線圈阻抗: 次級線圈阻抗: 絕緣電壓:23 dB 工作溫度范圍:- 40 C to + 85 C 端接類型:SMD/SMT 尺寸:6 mm L x 4.9 mm W x 1.6 mm H 產品:Splitters and Combiners |
| H-110-1 | 制造商:Hozan Tool Industrial Co Ltd 功能描述: |
| H1-101 | 制造商:MISCELLANEOUS 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。