- 您現在的位置：買賣IC網 > PDF目錄383056 > GX9533-CQY (Electronic Theatre Controls, Inc.) Serial Digital 8x9 Crosspoint PDF資料下載
參數資料
| 型號： | GX9533-CQY |
| 廠商： | Electronic Theatre Controls, Inc. |
| 英文描述： | Serial Digital 8x9 Crosspoint |
| 中文描述： | 串行數字8x9交叉點 |
| 文件頁數： | 6/8頁 |
| 文件大小： | 98K |
| 代理商： | GX9533-CQY |
521 - 41 - 03
6
G
DETAILED DESCRIPTION
DIFFERENTIAL INPUTS
The inputs to the GX9533 will accept both SMPTE 259M as
well as PECL input levels. The fully differential data path
provides low jitter data rates of up to 700Mb/s.
The main inputs (IN0..7) and expansion inputs (EXP0..7) are
normally connected to a biased differential data source.
The GX9533 inputs are not self biased, so unused inputs
should be connected as shown in Figure 3 or Figure 4.
Fig. 3 Preferred Termination Of Unused Inputs
Fig. 4 Alternate Termination of Unused Inputs
Terminating the inputs as shown in Figure 3 will provide the
highest noise immunity, since there is no possibility of noise
coupling into the unconnected input pin.
I/O ADDRESS SELECTION
The
GX9533
architecture which simplifies IN/OUT switch configuration.
has
a
versatile
LOAD/CONFIGURE
An output is normally connected to an input by a two stage
process:
Stage One: Loading The Configuration Into Latches
1. The output address is selected on the OA pins as
shown in Table 1.
2. The input address is selected on the IA pins as shown in
Table 2.
3. A LOAD pulse then transfers the output and input
addresses into the GX9533 LOAD latch.
The above three steps can be repeated up to eight times in
order to configure the latch for all eight outputs.
During step 3 above, if the LOADA pulse is also strobed,
the latch is configured to connect the selected input to the
ninth, auxiliary output.
Note that a QUIET mode is available as shown in Table 2. In
QUIET mode, the outputs are latched in a DC state with
OUT
X
= 1 and OUT
X
= 0.
Stage Two: Configuring The Matrix
A CONFIGURE strobe is applied to transfer the contents of
the LOAD latch into the CONFIG latch. This action will
cause the data flow through the GX9533 to be switched to
the new configuration. Refer to Figure 6 for detailed timing
information.
Note that any single output can be asynchronously
switched by having LOAD (or LOADA if desired) held high
while CONFIG is strobed.
IN
x
IN
x
GX9533
V
CC
1k
IN
X
IN
X
GX9533
V
CC
NC
TABLE 1: Output Address Selection
OA2
0A1
0A0
OUTPUT PORT
0
0
0
0
0
0
1
1
0
1
0
2
0
1
1
3
1
0
0
4
1
0
1
5
1
1
0
6
1
1
1
7
TABLE 2: Input Source Address Selection
IA3
IA2
IA1
IA0
INPUT
PORT
0
0
0
0
0
0
0
0
1
1
0
0
1
0
2
0
0
1
1
3
0
1
0
0
4
0
1
0
1
5
0
1
1
0
6
0
1
1
1
7
1
0
X
X
EXP
1
1
X
X
Quiet
Mode
相關PDF資料 |
PDF描述 |
|---|---|
| GX9533-CTY | Serial Digital 8x9 Crosspoint |
| GXB1000 | Industry’s Smallest GPS Receiver Module |
| GXB2000 | 16-Channel GPS Receiver Module |
| GXB2000 | Industry’s Smallest GPS Receiver Module |
| GXO-6451 | 5V SM OSCILLATOR |
相關代理商/技術參數 |
參數描述 |
|---|---|
| GX9533-CQYE3 | 制造商:Gennum Corporation 功能描述:Digital Crosspoint 8x9 0.85Gbps 100-Pin MQFP Tray |
| GX9533-CTY | 制造商:GENNUM 制造商全稱:GENNUM 功能描述:Serial Digital 8x9 Crosspoint |
| GXA18000 | 功能描述:整流器/與可變電容器 8mm 2-18pF 3 LEAD RoHS:否 制造商:Xicon 電容范圍:2.8 pF to 12.5 pF 容差: 電壓額定值:200 V 工作溫度范圍:- 35 C to + 85 C 端接類型:SMD/SMT 產品:Trimmer Capacitors - Ceramic Dielectric |
| GXA1W | 制造商:IVO 制造商全稱:Baumer IVO GmbH & Co. KG 功能描述:Absolute encoders - parallel |
| GXA1W.0B001 | 制造商:IVO 制造商全稱:Baumer IVO GmbH & Co. KG 功能描述:Absolute encoders - parallel |
發布緊急采購，3分鐘左右您將得到回復。