- 您現在的位置：買賣IC網 > PDF目錄370396 > GT4124 Trimmable Two Input Analog Mixers PDF資料下載
參數資料
| 型號： | GT4124 |
| 英文描述： | Trimmable Two Input Analog Mixers |
| 中文描述： | 微調兩個輸入模擬調音臺 |
| 文件頁數： | 8/15頁 |
| 文件大?。?/td> | 387K |
| 代理商： | GT4124 |
520 - 44 - 00
1) 0.5V Reference Adjustment (RV4)
METHOD:
Adjust RV4 for 0.5V
±
0.005V at pin 7 of the
GT4124 device.
[DO NOT touch this adjustment again.]
RV4
GND
CONTROL
INPUT
A - IN
B - IN
STROBE
OUT
O/C
GND
GND
2) Span, 50% Gain & Control Offset (RV1, RV2 & RV3)
RV1
1V P-P TRIANGLE
WAVE AT15 kHz
(V = 0 to 1V)
DC OFFSET = 0.5V
CONTROL
INPUT
A - IN
B - IN
STROBE
OUT
O/C
GND
1.0V
RV2
RV3
TO
SCOPE
CHOLD
METHOD:
Temporarily put a short circuit across the C
HOLD
capacitor on pin 2 of the device. This will disable
the clamping action.
Apply 1.0V DC to A-INPUT and 0V to INPUT-B (this
may be done by leaving INPUT-B open with the 75
resistor connected to ground).
Adjust RV1, RV2 and RV3 to produce the best 0 to 1V
(1V peak to peak) triangle waveform at the output.
These adjustments interact and so should be repeated
until the best waveform is obtained.
Remove the short across C
HOLD
.
TEST SET-UP FOR GT4124 MIXER BOARD
NOTE: Initially set all trim pots to mid-position.
3) Crossfade Balance (No adjustments)
METHOD:
The crossfade balance (control breakthrough) is
measured over frequency by using a Network
Analyser or Waveform Generator. Both INPUT-A and
INPUT-B are terminated with their 75
resistors.
The control voltage of 0-1V p-p with a 0.5V DC
offset is swept over the frequency range desired.
4) Frequency compensation (C
COMP
)
SET TO 1V
FOR A - IN
AND 0V FOR
B - IN TESTS
CONTROL
A - IN
B - IN
STROBE
OUT
O/C
FROM NETWORK ANALYSER
V
SIG
= 0 dBm
C
COMP
TO NETWORK
ANALYSER
METHOD:
Connect either the A-IN or B-IN pins to the Network
Analyser Output Port. Terminate these inputs with
50
resistors. Connect the OUTPUT to the Input Port
of the Network Analyser.
Set the voltage on the CONTROL to 1V in order to mea-
sure the frequency response of the A-INPUT.
Conversely, set the CONTROL voltage to 0V for the
B-INPUT measurement. Adjust the compen-
sating capacitor C
COMP
for the flattest frequency
response on both channels.
相關PDF資料 |
PDF描述 |
|---|---|
| GT4124-CDF | Analog Multiplier |
| GT4124-CKF | Analog Multiplier |
| GT560 | GT560 - Digitally Controlled Transconductance Block |
| GT560MCRO | Analog IC |
| GT560PLID | Analog IC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| GT4124-CDF | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Analog Multiplier |
| GT4124-CKF | 制造商:GENNUM 制造商全稱:GENNUM 功能描述:GT4124 Video Multiplier with Strobed DC Restore |
| GT4-1800 | 制造商:Power Acoustik 功能描述:Gothic Series 190W X 4Ch Autosound Amplifier 制造商:POWER ACOUSTIK 功能描述:AUTOSOUND AMPLIFIER GOTHIC SERIES 190W X 4CH |
| GT420 | 制造商:CORNELL DUBILIER ELECTRONICS 功能描述:Cap Ceramic 20pF 3000V SL 5% (10 X 6mm) Radial 9.5mm 85°C |
| GT422 | 制造商:Cornell Dubilier Electronics 功能描述:Cap Ceramic 22pF 3000V SL 5% (10 X 6mm) Radial 9.5mm 85°C |
發布緊急采購，3分鐘左右您將得到回復。