- 您現在的位置：買賣IC網 > PDF目錄370391 > GS9032-CVM SMPTE PDF資料下載
參數資料
| 型號： | GS9032-CVM |
| 英文描述： | SMPTE |
| 中文描述： | 符合SMPTE |
| 文件頁數： | 8/10頁 |
| 文件大?。?/td> | 705K |
| 代理商： | GS9032-CVM |
GENNUM CORPORATION
521 - 96 - 07
8 of 10
G
DETAILED DESCRIPTION
The GS9032 Serializer is a bipolar integrated circuit used to
convert parallel data into a serial format according to the
SMPTE 259M standard. The device encodes both eight and
ten bit TTL-compatible parallel signals producing serial
data rates up to 540Mb/s. It operates from a single five volt
supply and is packaged in a 44 pin TQFP.
Functional blocks within the device include the input
latches, sync detector, parallel to serial converter, SMPTE
scrambler, NRZ to NRZI converter, internal cable driver, PLL
for 10x parallel clock multiplication and lock detect. The
parallel data (PD0-PD9) and parallel clock (PCLKIN) are
applied via pins 1 through 11 respectively.
1. SYNC DETECTOR
The sync detector makes the system compatible with eight
or ten bit data. It looks for the reserved words 000-003 and
3FC-3FF in ten bit hexadecimal, or 00 and FF in eight bit
hexadecimal, used in the TRS-ID sync word. When the
occurrence of either all zeros or all ones at inputs PD2-PD9
is detected, the lower two bits PD0 and PD1 are forced to
zeros or ones respectively. For non-SMPTE standard
parallel data, the sync detector can be disabled through a
logic input, Sync Detect Disable (44).
2. SCRAMBLER
The scrambler is a linear feedback shift register used to
pseudo-randomize the incoming serial data according to
the fixed polynomial (X
9
+X
4
+1). This minimizes the DC
component in the output serial data stream. The NRZ to
NRZI converter uses another polynomial (X+1) to convert a
long sequence of ones to a series of transitions, minimizing
polarity effects. These functions can be disabled by setting
the BYPASS pin (31) high.
3. PHASE LOCKED LOOP
The PLL performs parallel clock multiplication and provides
the timing signal for the serializer. It is composed of a
phase/frequency detector (with no dead zone), charge
pump, VCO
,
a divide-by-ten counter, and a divide-by-two
counter.
The phase/frequency detector allows a wider capture range
and faster lock time than with a phase discriminator alone.
The discrimination of frequency eliminates harmonic
locking. With this type of discriminator, the PLL can be over-
damped for good stability without sacrificing lock time.
The charge pump delivers a 'charge packet' to the loop
filter which is proportional to the system phase error.
Internal voltage clamps are used to constrain the loop filter
voltage between approximately 1.8 and 3.4 volts.
The VCO is a differential low phase noise, factory trimmed
design that provides increased immunity to PBC noise and
precise control of the VCO centre frequency. The VCO can
operate in excess of 800MHz and has a pull range of ±15%
about the centre frequency. The single external resistor,
R
VCO
, sets the VCO frequency
(see Figure 12)
.
4. VCO CENTRE FREQUENCY SELECTION
For a given R
VCO
value, the VCO can oscillate at one of two
frequencies. When SS0=logic 1, the VCO centre frequency
corresponds to the
L
curve. For SS0=logic 0, the VCO
centre frequency corresponds to the
H
curve (
H
is
approximately 1.5 x
L
).
Fig. 12
The recommended R
VCO
value for auto rate SMPTE 259M
applications is 374
(
see the Typical Application Circuit
).
This value prevents false standards indication in auto mode.
For non-SMPTE applications (where data rates are x2
harmonically related) use Figure 12 to determine the R
VCO
values.
The VCO and an internal divider generate the PLL clock.
Divider moduli of 1, 2, and 4 allow the PLL to lock to data
rates from 143Mb/s to 540Mb/s. The divider modulus is set
by the AUTO/MAN, and SS[2:0] pins (
see Truth Table for
further details
). In addition, a manually selectable modulus
8 divider allows operation at data rates as low as 18Mb/s
when R
VCO
is increased to 1k
.
When the loop is not locked, the lock detect circuit mutes
the serial data outputs. When the loop is locked, the Lock
Detect output is available from pin 20 and is HIGH.
The true and complement serial data, SDO and SDO, are
available from pins 24, 25, 27 and 28. These outputs drive
four 75
co-axial cables with SMPTE level serial digital
video signals. To disable the outputs from pins 27 and 28
(SDO1, SDO1), remove the resistor connected to the R
SET1
pin (30) and float the SDO1 ENABLE pin (19).
NOTE: Do NOT connect pin 19 to V
CC
.
R
SET
calculation:
where R
LOAD
= R
PULL-UP
|| Z
0
100
200
300
400
500
600
700
800
0
200
400
600
800
1000
1200 1400
1600 1800
V
R
VCO
(
)
H
L
SSO=1
SSO=0
R
SET
1.154
--------------------------------------
R
SDO
×
=
相關PDF資料 |
PDF描述 |
|---|---|
| GS9035 | GENLINX II Serial Digital Reclocker |
| GS9035C | 143-360Mb/s Reclocker. |
| GS9060* | 270Mb/s Reclocking Deserializer with EDH for SDI and DVB-ASI. 3.3/1.8V supply. |
| GS9062* | 270Mb/s Serializer with EDH for SDI and DVB-ASI. 3.3/1.8V supply. |
| GS9064 | Telecomm/Datacomm |
相關代理商/技術參數 |
參數描述 |
|---|---|
| GS9032-CVME3 | 制造商:Gennum Corporation 功能描述:Digital Video Serializer 44-Pin TQFP |
| GS9035 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:GENLINX II Serial Digital Reclocker |
| GS9035A | 制造商:GENNUM 制造商全稱:GENNUM 功能描述:Serial Digital Reclocker |
| GS9035ACPJ | 制造商:Gennum Corporation 功能描述: |
| GS9035ACPJE3 | 制造商:Semtech Corporation 功能描述:Reclocker 28-Pin PLCC 制造商:Gennum Corporation 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。