- 您現在的位置：買賣IC網 > PDF目錄383055 > GS881Z36 (GSI TECHNOLOGY) 8Mb Pipelined and Flow Through Synchronous NBT SRAM(8M位流水線式和流通型同步NBT靜態RAM) PDF資料下載
參數資料
| 型號： | GS881Z36 |
| 廠商： | GSI TECHNOLOGY |
| 英文描述： | 8Mb Pipelined and Flow Through Synchronous NBT SRAM(8M位流水線式和流通型同步NBT靜態RAM) |
| 中文描述： | 8MB的流水線和流量，通過同步唑的SRAM（800萬位流水線式和流通型同步唑靜態內存） |
| 文件頁數： | 26/34頁 |
| 文件大?。?/td> | 522K |
| 代理商： | GS881Z36 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁當前第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁
Rev: 1.10 8/2000
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com
26/34
1998, Giga Semconductor, Inc.
Preliminary
.
GS881Z18/36T-11/100/80/66
(Private) instructions. Some Public instructions, are mandatory for 1149.1 compliance. Optional Public instructions must be
implemented in prescribed ways. Although the TAP controller in this device follows the 1149.1 conventions, it is not 1194.1-
compliant because some of the mandatory instructions are not fully implemented. The TAP on this device may be used to monitor
all input and I/O pads, but cannot be used to load address, data or control signals into the RAM or to preload the I/O buffers.This
device will not perform EXTEST, INTEST or the SAMPLE/PRELOAD command.
When the TAP controller is placed in Capture-IR state the two least significant bits of the instruction register are loaded with 01.
When the controller is moved to the Shift-IR state the Instruction Register is placed between TDI and TDO. In this state the desired
instruction is serially loaded through the TDI input (while the previous contents are shifted out at TDO). For all instructions, the
TAP executes newly loaded instructions only when the controller is moved to Update-IR state. The TAP instruction set for this
device is listed in the following table.
JTAG Tap Controller State Diagram
Instruction Descriptions
BYPASS
When the BYPASS instruction is loaded in the Instruction Register the Bypass Register is placed between TDI and TDO. This occurs when
the TAP controller is moved to the Shift-DR state. This allows the board level scan path to be shortened to facilitate testing of other devices
in the scan path.
SAMPLE/PRELOAD
SAMPLE/PRELOAD is a Standard 1149.1 mandatory public instruction. When the SAMPLE/PRELOAD instruction is loaded in the Instruc-
tion Register, moving the TAP controller into the Capture-DR state loads the data in the RAMs input and I/O buffers into the Boundary Scan
Select DR
Capture DR
0
Shift DR
Exit1 DR
Pause DR
Exit2 DR
Update DR
1
Select IR
Capture IR
0
Shift IR
Exit1 IR
Pause IR
Exit2 IR
Update IR
1
Test Logic Reset
Run Test Idle
0
1
0
1
1
0
1
1
1
0
0
1
1
0
0
0
0
1
1
0
0
0
0
0
1
1
1
1
相關PDF資料 |
PDF描述 |
|---|---|
| GS882Z18B-100 | 8Mb Pipelined and Flow Through Synchronous NBT SRAMs |
| GS882Z18B-100I | 8Mb Pipelined and Flow Through Synchronous NBT SRAMs |
| GS882Z18B-11 | 8Mb Pipelined and Flow Through Synchronous NBT SRAMs |
| GS882Z18B-11I | 8Mb Pipelined and Flow Through Synchronous NBT SRAMs |
| GS882Z18B-66 | 8Mb Pipelined and Flow Through Synchronous NBT SRAMs |
相關代理商/技術參數 |
參數描述 |
|---|---|
| GS881Z36AT-133 | 制造商:GSI 制造商全稱:GSI Technology 功能描述:9Mb Pipelined and Flow Through Synchronous NBT SRAM |
| GS881Z36AT-133I | 制造商:GSI 制造商全稱:GSI Technology 功能描述:9Mb Pipelined and Flow Through Synchronous NBT SRAM |
| GS881Z36AT-150 | 制造商:GSI 制造商全稱:GSI Technology 功能描述:9Mb Pipelined and Flow Through Synchronous NBT SRAM |
| GS881Z36AT-150I | 制造商:GSI 制造商全稱:GSI Technology 功能描述:9Mb Pipelined and Flow Through Synchronous NBT SRAM |
| GS881Z36AT-166 | 制造商:GSI 制造商全稱:GSI Technology 功能描述:9Mb Pipelined and Flow Through Synchronous NBT SRAM |
發布緊急采購，3分鐘左右您將得到回復。