- 您現在的位置：買賣IC網 > PDF目錄370378 > GS-D500A (意法半導體) 100V/5A STEP AND MICROSTEP DRIVE BOARD FOR STEPPER MOTORS PDF資料下載
參數資料
| 型號： | GS-D500A |
| 廠商： | 意法半導體 |
| 英文描述： | 100V/5A STEP AND MICROSTEP DRIVE BOARD FOR STEPPER MOTORS |
| 中文描述： | 100V/5A STEP和微步驅動板步進電機 |
| 文件頁數： | 7/10頁 |
| 文件大?。?/td> | 99K |
| 代理商： | GS-D500A |
7/10
A1 - SUPPLY VOLTAGE
THE POWER SUPPLY MUST BE TURNED OFF WHEN
PLUGGING OR UNPLUGGING THE BOARD
The supply pins are:
J2-1 for Motor SupplyVoltage
J2-3for Auxiliary Voltage
J2-2,4 for Groundrail
The other supply voltages needed by the boards
are internallygenerated.
If an undervoltagecondition is detected(Vs < 10V)
the GS-D500Ais automatically disabled and a led
is activated.
The Motor Supplyvoltageis in the range from 12 to
100V,the Auxiliary voltage from 11 to 13V.
At power-onthe Auxiliary Supply voltage must
be applied before the Motor Supply voltage,
while at power-off the Motor Supply voltage
must be removed before the Auxiliary voltage.
A2- FULL-STEP/HALF-STEP/MICROSTEPPRO-
GRAMMINGBY HARDWARE
Thenumberof microstepsperstepisfieldprogram-
mable. The digitized sine and cosine functions,
required bya microsteppingcontrol,are stored in a
Lock-Up-Table inside the GS-D500A.
Two options are provided for the proper mi-
crosteps/steprate selection.
Threeswitches (SW1, SW2,SW3) areavailable on
the front edge of the board.
The full-step/half-step/microstep mode is defined
by the following table.
SW1
SW2
SW3
MODE
OFF
ON
OFF
Half step
ON
ON
OFF
125 microsteps/step
ON
OFF
ON
25 microsteps/step
OFF
ON
ON
5 microsteps/step
ON
ON
ON
Full step
The switches are in OFF condition when the knob
is pulled versus the board edge. Invalid combina-
tions disable the board.
A2.1 - MICROSTEP PROGRAMMING BY HOST
COMPUTER
The microsteps/step rate can also be remotely
changed by using the three logic inputs available
on the J3 connector (pins 4,12 and 15) that cor-
responds, respectively, to SW1, SW2, SW3.
The interactionbetweenlogicsignalsandhardware
switches is shown in fig. 4.
Figure 7. Remote microsteppingprogramming
To operate the logic pins of the J3 connector,the
three internalswitches must be in the OFFstate.
A3 - CURRENT REDUCTION AT REST
Phase current can be reduced when the motor is
stopped if SW6 is open.
Current reductionis operative about1 second after
the lastclock pulse.
GS-D500A
相關PDF資料 |
PDF描述 |
|---|---|
| GS-DC200 | STEPPER MOTOR CONTROL AND DRIVE SYSTEM FAMILY |
| GS-DC200S | STEPPER MOTOR CONTROL AND DRIVE SYSTEM FAMILY |
| GS-DC200SS | STEPPER MOTOR CONTROL AND DRIVE SYSTEM FAMILY |
| GS-F8MB-SIMM | 8MByte SIMM Flash Memory Module(8M字節SIMM閃速存儲器模塊) |
| GS-M51212 | Analog IC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| GSD504020GP2 | 制造商:Pentair Technical Products / Hoffman 功能描述:GLOBAL WALL-MOUNT ENC.,GLAND P |
| GSD504020GP2SS | 制造商:Pentair Technical Products / Hoffman 功能描述:GLOBAL WALL-MOUNT ENCLOSURE, GLAND P |
| GSD505020GP3 | 制造商:Pentair Technical Products / Hoffman 功能描述:GLOBAL WALL MOUNT ENCLOSURE |
| GSD600 | 功能描述:環境檢測設備 GAS LEAK DETECT FOR METHANE AND PROPANE RoHS:否 制造商:Fluke 設備類型:Vibration Meter 測量儀器:Vibration |
| GSD605020GP3 | 制造商:Pentair Technical Products / Hoffman 功能描述:GLOBAL WALL-MOUNT ENC.,GLAND P |
發布緊急采購，3分鐘左右您將得到回復。