- 您現在的位置：買賣IC網 > Datasheet目錄61 > GP1A52HRJ00F (Sharp Microelectronics)PHOTOINTER OPIC SLOT 3.0MM PCB Datasheet資料下載
參數資料
| 型號： | GP1A52HRJ00F |
| 廠商： | Sharp Microelectronics |
| 文件頁數： | 7/12頁 |
| 文件大小： | 0K |
| 描述： | PHOTOINTER OPIC SLOT 3.0MM PCB |
| 產品變化通告： | Internal Chip Change 04/May/2007 |
| 標準包裝： | 100 |
| 系列： | OPIC™ |
| 檢測距離： | 0.118"（3mm） |
| 檢測方法： | 可傳導的 |
| 輸出配置： | 上拉電阻，緩沖器 |
| 安裝類型： | 通孔 |
| 電流 - 電源： | 1.7mA |
| 電源電壓： | 4.5 V ~ 17 V |
| 響應時間： | 1µs，0.05µs |
| 封裝/外殼： | PCB 安裝 |
| 產品目錄頁面： | 2776 (CN2011-ZH PDF) |
| 其它名稱： | 425-1950-5 |
7
Sheet No.: D3-A03701EN
GP1A52HRJ00F
?SPAN class="pst GP1A52HRJ00F_2584186_4">Design Considerations
?/DIV>
Recommended operating conditions
Parameter
Symbol MIN.
TYP.
MAX.
Unit
Output current
I
O
16
mA
Forward current
I
F
10
20
mA
Operating terperature
T
opr
0
70
贑
?/DIV>
Notes about static electricity
Transisiter of detector side in bipolar con guration may be damaged by static electricity due to its minute
design.
When handing these devices, general countermeasure against static electricity should be taken to avoid
breakdown of devices or degradation of characteristics.
?/DIV>
Design guide
1) Prevention of detection error
To prevent photointerrupter from faulty operation caused by external light, do not set the detecting face to
the external light.
2) In order to stabilize power supply line, connect a by-pass capacitor of more than 0.01糉 between V
CC
and
GND near the device.
3) Position of opaque board
Opaque board shall be installed at place 4mm or more from the top of elements.
(Example)
4mm or more
This product is not designed against irradiation and incorporates non-coherent IRED.
?/DIV>
Degradation
In general, the emission of the IRED used in photocouplers will degrade over time.
In the case of long term operation, please take the general IRED degradation (50% degradation over 5
years) into the design consideration.
相關PDF資料 |
PDF描述 |
|---|---|
| GP1A52LRJ00F | PHOTOINTER OPIC SLOT 3.0MM PCB |
| GP1A53HRJ00F | PHOTOINTER OPIC SLOT 5.0MM PCB |
| GP1A57HRJ00F | PHOTOINTER OPIC SLOT 10MM PCB |
| GP1A58HRJ00F | PHOTOINTER OPIC SLOT 5.0MM PCB |
| GP1A75E | PHOTOINTER OPIC SLOT 5.0MM W/CON |
相關代理商/技術參數 |
參數描述 |
|---|---|
| GP1A52LR | 功能描述:PHOTOINTER OPIC SLOT 3.0MM PCB RoHS:否 類別:傳感器，轉換器 >> 光學 - 光斷續器 - 槽型 - 邏輯輸出 系列:OPIC™ 產品變化通告:Product Discontinuation 03/Dec/2009 標準包裝:50 系列:OPTOLOGIC® 檢測距離:0.197"（5mm） 檢測方法:可傳導的 輸出配置:NPN - 開路集電極，緩沖器 安裝類型:通孔 電流 - 電源:5mA 電源電壓:4.5 V ~ 16 V 響應時間:70ns 封裝/外殼:PCB 安裝 |
| GP1A52LRJ00F | 功能描述:光學開關（透射型，光電IC輸出） Case Type Photntrptr 3.0mm 0.5mm Screw RoHS:否 制造商:Optek 輸出設備:Totem Pole, Buffer 槽寬:3.18 mm 光圈寬度:1.27 mm 正向電流:40 mA 最大工作溫度:+ 70 C 最小工作溫度:- 40 C 封裝: |
| GP1A53HR | 功能描述:PHOTOINTER OPIC SLOT 5.0MM PCB RoHS:否 類別:傳感器，轉換器 >> 光學 - 光斷續器 - 槽型 - 邏輯輸出 系列:OPIC™ 產品變化通告:Product Discontinuation 03/Dec/2009 標準包裝:50 系列:OPTOLOGIC® 檢測距離:0.197"（5mm） 檢測方法:可傳導的 輸出配置:NPN - 開路集電極，緩沖器 安裝類型:通孔 電流 - 電源:5mA 電源電壓:4.5 V ~ 16 V 響應時間:70ns 封裝/外殼:PCB 安裝 |
| GP1A53HRJ00F | 功能描述:光學開關（透射型，光電IC輸出） Case Type Photntrptr 3.0mm 0.5mm Screw RoHS:否 制造商:Optek 輸出設備:Totem Pole, Buffer 槽寬:3.18 mm 光圈寬度:1.27 mm 正向電流:40 mA 最大工作溫度:+ 70 C 最小工作溫度:- 40 C 封裝: |
| GP1A53HR-J00F | 制造商:Sharp Microelectronics Corporation 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。