- 您現在的位置：買賣IC網 > PDF目錄370366 > GMS81C5016-XXXD MICROCONTROLLER|8-BIT|CMOS|SOP|28PIN|PLASTIC PDF資料下載
參數資料
| 型號： | GMS81C5016-XXXD |
| 英文描述： | MICROCONTROLLER|8-BIT|CMOS|SOP|28PIN|PLASTIC |
| 中文描述： | 單片機| 8位|的CMOS |?？苵 28腳|塑料 |
| 文件頁數： | 68/93頁 |
| 文件大小： | 853K |
| 代理商： | GMS81C5016-XXXD |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁當前第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁
GMS81C1404/GMS81C1408
66
June. 2001 Ver 1.2
Release the STOP mode
The exit from STOP mode is hardware reset or external in-
terrupt. Reset re-defines all the Control registers but does
not change the on-chip RAM. External interrupts allow
both on-chip RAM and Control registers to retain their val-
ues. If I-flag = 1, the normal interrupt response takes place.
If I-flag = 0, the chip will resume execution starting with
the instruction following the STOP instruction. It will not
vector to interrupt service routine. (refer to Figure 19-1 )
By reset, exit from Stop mode is shown in Figure 19-3
.When exit from Stop mode by external interrupt, enough
oscillation stabilization time is required to normal opera-
tion. Figure 19-2 shows the timing diagram. When release
the Stop mode, the Basic interval timer is activated on
wake-up. It is increased from 00
H
until FF
H
. The count
overflow is set to start normal operation. Therefore, before
STOP instruction, user must be set its relevant prescaler di-
vide ratio to have long enough time (more than 20msec).
This guarantees that oscillator has started and stabilized..
Figure 19-1 STOP Releasing Flow by Interrupts
Figure 19-2 Timing of STOP Mode Release by External Interrupt
IEXX
=0
=1
STOP
INSTRUCTION
STOP Mode
Interrupt Request
STOP Mode Release
I-FLAG
=1
Interrupt Service Routine
Next
INSTRUCTION
=0
Master Interrupt
Enable Bit PSW[2]
Corresponding Interrupt
Enable Bit (IENH, IENL)
~
STOP Mode
Normal Operation
Oscillator
(X
IN
pin)
~
~
N+1
N
N+2
00
01
FE
FF
00
00
N-1
N-2
~
~
~
~
~
Clear Basic Interval Timer
STOP Instruction Execution
Normal Operation
Stabilizing Time
t
ST
> 20mS
Internal
Clock
External
Interrupt
BIT
Counter
~
相關PDF資料 |
PDF描述 |
|---|---|
| GMS81C5016-XXXDT | MICROCONTROLLER|8-BIT|CMOS|SOP|28PIN|PLASTIC |
| GMS81C5016-XXXPL | MICROCONTROLLER|8-BIT|CMOS|LDCC|44PIN|PLASTIC |
| GMS81C5016-XXXPLT | MICROCONTROLLER|8-BIT|CMOS|LDCC|44PIN|PLASTIC |
| GMS81C5016-XXXQ | MICROCONTROLLER|8-BIT|CMOS|QFP|44PIN|PLASTIC |
| GMS81C5016-XXXQT | MICROCONTROLLER|8-BIT|CMOS|QFP|44PIN|PLASTIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| GMS81C5016-XXXDT | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:MICROCONTROLLER|8-BIT|CMOS|SOP|28PIN|PLASTIC |
| GMS81C5016-XXXPL | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:MICROCONTROLLER|8-BIT|CMOS|LDCC|44PIN|PLASTIC |
| GMS81C5016-XXXPLT | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:MICROCONTROLLER|8-BIT|CMOS|LDCC|44PIN|PLASTIC |
| GMS81C5016-XXXQ | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:MICROCONTROLLER|8-BIT|CMOS|QFP|44PIN|PLASTIC |
| GMS81C5016-XXXQT | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:MICROCONTROLLER|8-BIT|CMOS|QFP|44PIN|PLASTIC |
發布緊急采購，3分鐘左右您將得到回復。