- 您現在的位置：買賣IC網 > PDF目錄67620 > GB160160BSYAAMDB-V00 (Jewel Hill Electronic Co., Ltd.) CAP,ELEC,RAD,NP,1UF,100V, 85C,20%,5X11MM PDF資料下載
參數資料
| 型號： | GB160160BSYAAMDB-V00 |
| 廠商： | Jewel Hill Electronic Co., Ltd. |
| 英文描述： | CAP,ELEC,RAD,NP,1UF,100V, 85C,20%,5X11MM |
| 中文描述： | 規格液晶模塊 |
| 文件頁數： | 15/24頁 |
| 文件大小： | 290K |
| 代理商： | GB160160BSYAAMDB-V00 |
GB160160B
VER: 2.0
- 21 -
Issue date: 2006/08/04
JEWEL HILL ELECTRONIC CO.,LTD.
(1) Make certain that you are grounded when handing LCM.
(2) Before removing LCM from its packing case or incorporating it into a set, be sure the module and
your body have the same electric potential.
(3) When soldering the terminal of LCM, make certain the AC power source for the soldering iron
does not leak.
(4) When using an electric screwdriver to attach LCM, the screwdriver should be of ground
potentiality to minimize as much as possible any transmission of electromagnetic waves produced
sparks coming from the commutator of the motor.
(5) As far as possible, make the electric potential of your work clothes and that of the workbenches to
the ground potential.
(6) To reduce the generation of electro-static discharge, be careful that the air in the work is not too
dried. A relative humidity of 50%-60% is recommended.
11.4 PRECAUTIONS FOR OPERATION
(1) Viewing angle varies with the change of liquid crystal driving voltage (Vo). Adjust Vo to show
the best contrast.
(2) Driving the LCD in the voltage above the limit will shorten its lifetime.
(3) Response time is greatly delayed at temperature below the operating temperature range. However,
this does not mean the LCD will be out of the order. It will recover when it returns to the specified
temperature range.
(4) If the display area is pushed hard during operation, the display will become abnormal. However, it
will return to normal if it is turned off and then on.
(5) Condensation on terminals can cause an electrochemical reaction disrupting the terminal circuit.
Therefore, this product must be used and stored within the specified condition of 23±5°C,
45±20%RH.
(6) When turning the power on, input each signal after the positive/negative voltage becomes stable.
11.5 SAFETY
(1) It is recommended to crush damaged or unnecessary LCDs into pieces and wash them off with
solvents such as acetone and ethanol, which should later be burned.
thoroughly with soap and water.
相關PDF資料 |
PDF描述 |
|---|---|
| GB160160BSYAAMLA-V00 | CAP,ELEC,RAD,NP,1UF,25V, HF,85C,20%,8X11MM |
| GB160160BSYAAMLB-V00 | AP,ELEC,RAD,NP,1UF,50V, 85C,20%,5X11MM,INCREMENTSof10 |
| GB160160BSYAAMUA-V00 | CAP,ELEC,RAD,NP,10UF,25V, 85C,20%,5X11MM |
| GB160160BSYAAMUB-V00 | CAP,ELEC,RAD,NP,10UF,25V, HF,85C,20%,8X14MM |
| GB160160BSYAANDA-V00 | CAP,ELEC,RAD,NP,10UF,50V, HF,85C,20%,10X15MM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| GB160160BSYAAMLA-V00 | 制造商:JHE 制造商全稱:Jewel Hill Electronic 功能描述:SPECIFICATIONS FOR LCD MODULE |
| GB160160BSYAAMLB-V00 | 制造商:JHE 制造商全稱:Jewel Hill Electronic 功能描述:SPECIFICATIONS FOR LCD MODULE |
| GB160160BSYAAMUA-V00 | 制造商:JHE 制造商全稱:Jewel Hill Electronic 功能描述:SPECIFICATIONS FOR LCD MODULE |
| GB160160BSYAAMUB-V00 | 制造商:JHE 制造商全稱:Jewel Hill Electronic 功能描述:SPECIFICATIONS FOR LCD MODULE |
| GB160160BSYAANDA-V00 | 制造商:JHE 制造商全稱:Jewel Hill Electronic 功能描述:SPECIFICATIONS FOR LCD MODULE |
發布緊急采購，3分鐘左右您將得到回復。