- 您現在的位置：買賣IC網 > PDF目錄1995 > FT8010UMX (Fairchild Semiconductor)IC RESET TIMER CONF DELAY 10UMLP PDF資料下載
參數資料
| 型號： | FT8010UMX |
| 廠商： | Fairchild Semiconductor |
| 文件頁數： | 7/12頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC RESET TIMER CONF DELAY 10UMLP |
| 標準包裝： | 5,000 |
| 類型： | 可編程計時器 |
| 電源電壓： | 1.8 V ~ 5 V |
| 電流 - 電源： | 100µA |
| 工作溫度： | -40°C ~ 85°C |
| 封裝/外殼： | 10-UFQFN |
| 包裝： | 帶卷 (TR) |
| 供應商設備封裝： | 10-UMLP |
| 安裝類型： | 表面貼裝 |
2009 Fairchild Semiconductor Corporation
www.fairchildsemi.com
FT8010 Rev. 1.0.8
4
FT8010
—
Reset
Timer
with
Configurable
Delay
Time
Functional Description
The FT8010 reset timer uses an internal oscillator and a
two-stage, 21-bit counter to determine when the output
pins switch. Time N is set by the hard-wired logic level
of the DSR pin. N is either 7.5 ±20% seconds for
DSR=LOW or 11.25 ±20% seconds for DSR=HIGH.
Table 1.
FT8010 Truth Table
DSR
Reset Timer ( +-20% )
0
7.50s
1
11.25s
The two input pins, /SR0 and /SR1, drive voltage
comparators that compare the voltage on the input with
the voltage set by the reference block. A low input signal
on both /SR0 and /SR1 starts the oscillator. The
oscillator sends data pulses to the digital core, which
includes the counter. There are two scenarios for
counting, as described below: short duration and long
duration. In the short-duration scenario, outputs /RST1
and RST2 are not affected. In the long duration
scenario, the outputs change state after time N. The
outputs return to their original states when a HIGH input
signal occurs on either /SR0 or /SR1.
The /RST1 output is an open-drain driver. When the count
time exceeds time N, the /RST1 output drives LOW. The
RST2 output is a push-pull driver. When the count time
exceeds time N, the RST2 output drives HIGH.
The TRIG pin should be tied GND or LOW during
normal operation. The TRIG pin is a test mode pin used
for SCAN testing.
Application Note
IMPORTANT
: The DSR pin must be tied to VCC or GND
to provide a HIGH or LOW voltage level. The voltage
level on the DSR pin determines the length of the
configurable delay. It is important that the voltage level
on the DSR pin not change during normal operation.
The DSR pin must be tied directly to VCC or GND before
SR0 or SR1 buttons go LOW. Do not use pull-up or pull-
down resistors on the DSR pin.
Short Duration (tW < N)
In this case, both input /SR0 and /SR1 are LOW for a
duration tW which is shorter than time N. When an input
goes LOW, the internal timer starts counting. The input
goes HIGH before time N. The timer stops counting and
resets and no changes occur on the outputs (see Figure 4).
/SR0
/SR1
/RST1
/RST2
Description
L
H
L
The timer starts counting when both inputs go LOW. The timer stops
counting and resets when either input goes HIGH. No changes occur on the
outputs, Both /SR0 and /SR1 need to be LOW to activate (start) the timer.
L
H
L
Figure 4.
Short Duration Waveform
相關PDF資料 |
PDF描述 |
|---|---|
| FTS125-COO-010.0M | IC GPS BASED TIMING MOD (OCXO) |
| FTS125-CTV-010.0M | IC GPS BASED TIMING MOD (TCXO) |
| FTS250-010.0M | IC GPS BASED TIMING MOD (TCXO) |
| FTS375-010.0M | IC GPS BASED TIMING MOD (OCXO) |
| HD3-6408-9Z | IC ASMA ADT CMOS 1.25MHZ 24DIP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| FT8011 | 制造商:Black Box Corporation 功能描述:MINI NYL CABLE TIES 0.1"W X 4.0"L,BLK-100PK |
| FT801-31 | 功能描述:WIRE STRIPPER,THERMAL,DIGITAL,FT 制造商:american hakko products, inc. 系列:* 零件狀態:在售 標準包裝:1 |
| FT801Q-R | 功能描述:IC TFT LCD CONTROLLER 48VQFN 制造商:ftdi, future technology devices international ltd 系列:- 包裝:剪切帶（CT） 零件狀態:有效 類型:控制器 應用:視頻 安裝類型:表面貼裝 封裝/外殼:48-VFQFN 裸露焊盤 供應商器件封裝:48-VQFN（7x7） 標準包裝:1 |
| FT8020 | 制造商:Black Box Corporation 功能描述:MINI NYL CABLE TIES 0.1"W x 8.0"L,BLCK-100PK |
| FT805-E | 制造商:Black Box Corporation 功能描述:FT805 230V VERSION |
發布緊急采購，3分鐘左右您將得到回復。