- 您現在的位置：買賣IC網 > PDF目錄67592 > FSM6403MTC (FAIRCHILD SEMICONDUCTOR CORP) SPECIALTY CONSUMER CIRCUIT, PDSO20 PDF資料下載
參數資料
| 型號： | FSM6403MTC |
| 廠商： | FAIRCHILD SEMICONDUCTOR CORP |
| 元件分類： | 消費家電 |
| 英文描述： | SPECIALTY CONSUMER CIRCUIT, PDSO20 |
| 封裝： | LEAD FREE, MO-153AC, TSSOP-20 |
| 文件頁數： | 4/14頁 |
| 文件大?。?/td> | 670K |
| 代理商： | FSM6403MTC |
2005 Fairchild Semiconductor Corporation
www.fairchildsemi.com
FMS6403 Rev. 1.0.4
12
FM
S6403
—
Triple
Video
D
rivers
wit
h
Select
able
H
D
/PS/SD
B
y
pass
Filt
ers
f
o
rR
G
B
and
YPbPr
Signals
Applications Information
Input Circuitry
The DC restore circuit requires a source impedance
(RSOURCE = RS || RT) of less than or equal to 150 for
correct operation. Driving the FMS6403 with a high-
impedance source (e.g. a DAC loaded with 330) does
not yield optimum results. Refer Figure 2 for details.
Output Drive
The FMS6403 is specified to operate with output
currents typically less than 60mA, more than sufficient
for a dual (75) video load. Internal amplifiers are
current limited to approximately 100mA and should
withstand
brief-duration,
short-circuit
conditions;
however, this capability is not guaranteed.
The maximum specified input voltage of 1.5VPP can be
sustained for all inputs. When the input is clamped to
1.125V, this does not result in a meaningful output
signal. With a gain of 6dB, the output should be 1.125V
±1.5V, which is not possible since the output cannot
drive below ground. This condition will not damage the
part; however, the output will be clipped. For signals
clamped to 250mV, this does not occur.
Signals at mid-scale during SYNC (Pb and Pr) must be
clamped to 1.125V. Signals that are at their lowest
during SYNC (Y, R, G, B) must be clamped to 250mV
for proper operation. Clamping a Pr signal to 250mV
results in clipping the bottom of the signal.
The
220F
capacitor
coupled
with
the
150
termination, as shown in the Figure 2, forms a high-
pass filter that blocks the DC while passing the video
frequencies and avoiding tilt. Any value lower than
220μF creates problems, such as video tilt. Higher
values, such as 470μF - 1000μF, are the most optimal
output coupling capacitor. By AC coupling, the average
DC level is zero and the output voltages of all channels
is centered ~zero.
Sync Recovery
The FMS6403 typically recovers bi-level sync with
amplitude greater than 100mV (33% compressed
relative to the nominal 300mV amplitude). The
FMS6403 looks for the lowest signal voltage and
clamps this to approximately 250mV at the output.
Tri-level sync may not be compressed more than 5%
(15mV) for correct operation. Tri-level sync is located by
finding the edges of the tri-level pulse and running a
timer to operate the clamp during the back porch
interval.
The selection of the 8MHz or 15MHz filters enables bi-
level sync recovery. Selection of the 30MHz filter or
bypass mode enables tri-level sync recovery. Bi-level
and tri-level sync recovery are not interchangeable. See
the Sync Processing section for more information.
Power Dissipation
The output drive configuration must be considered
when calculating overall power dissipation. Care must
be taken not to exceed the maximum die junction
temperature. The following example can be used to
calculate the FMS6403’s power dissipation and internal
temperature rise:
TJ = TA + Pd ΘJA
where:
PD = PCH1 + PCH2 + PCH3
and:
PCHx = VS ICH - (VO
2/RL)
where:
VO = 2VIN + 0.280V
ICH = (ICC / 3) + (VO/RL)
VIN = RMS value of input signal
ICC = 90mA
VS = 5V
RL = channel load resistance
(1)
Board layout can also affect thermal characteristics.
Refer to the Layout Considerations Section for more
information.
The FMS6403 is specified to operate with
output currents typically less than 60mA, more than
sufficient for a single (150) video load. Internal
amplifiers are current limited to a maximum of 100mA
and should withstand brief duration short circuit
conditions, however this capability is not guaranteed.
Layout Considerations
General layout and supply bypassing play major roles in
high-frequency
performance
and
thermal
characteristics. Fairchild offers an evaluation board,
FMS6403DEMO, to guide layout and aid device testing
and characterization. The FMS6403DEMO is a four-
layer board with a full power and ground planes. For
optimum results, follow the steps below as a basis for
high-frequency layout:
Include 10μF and 0.1μF ceramic bypass
capacitors.
Place the 10μF capacitor within 0.75 inches of the
power pin.
Place the 0.1μF capacitor within 0.1 inches of the
power pin.
Connect all external ground pins as tightly as
possible, preferably with a large ground plane
under the package.
Layout channel connections to reduce mutual trace
inductance.
Minimize all trace lengths to reduce series
inductances. If routing across a board, place devise
such that longer traces are at the inputs rather than
the outputs.
If using multiple, low-impedance DC-coupled outputs;
special layout techniques can help dissipate heat. For
dual-layer boards, place a 0.5-inch to 1-inch (1.27cm to
2.54cm) square ground plane directly under the device
and on the bottom side of the board. Use multiple vias
to connect the ground planes. For multi-layer boards,
additional planes (connected with vias) can be used for
additional thermal improvements.
Worst-case additional die power due to DC loading can
be estimated at (VCC
2/4Rload) per output channel. This
assumes a constant DC output voltage of VCC
2. For 5V
VCC with a dual DC video load, add 25/(475) = 83mW,
per channel.
相關PDF資料 |
PDF描述 |
|---|---|
| FSQ0765RQ | 3.92 A SWITCHING CONTROLLER, 75.8 kHz SWITCHING FREQ-MAX, ZFM6 |
| FUSION878A | COLOR SIGNAL DECODER, PQFP128 |
| FVXO-HC53BR-FREQ | VCXO, CLOCK, 0.75 MHz - 250 MHz, HCMOS OUTPUT |
| FVXO-HC72BR-FREQ | VCXO, CLOCK, 0.75 MHz - 180 MHz, HCMOS OUTPUT |
| FVXO-HC73B-FREQ | VCXO, CLOCK, 0.75 MHz - 250 MHz, HCMOS OUTPUT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| FSM6403MTC20X | 制造商:FAIRCHILD 制造商全稱:Fairchild Semiconductor 功能描述:Triple Video Drivers with Selectable HD/PS/SD Bypass Filters for RGB and YPbPr Signals |
| FSM6J | 功能描述:SWITCH TACTILE SPST-NO 0.05A 12V RoHS:是 類別:開關 >> 觸摸 系列:FSMJ 標準包裝:2,000 系列:LPH 電路:SPST-NO 開關功能:關-瞬時 觸點額定電壓:0.05A @ 12VDC 觸動器類型:標準 安裝類型:通孔 從引腳算起，致動器距離 PCB 的高度:7.00mm 致動器方向:頂部觸動 端接類型:PC 引腳 外形:6.00mm x 6.00mm 發光:不發光 發光電壓:- 發光類型，顏色:- 操作力:160gf 防護等級:IP40 特點:觸摸反饋 包裝:帶卷 (TR) 觸動器材料:- 開關行程:0.25mm 機械壽命:100,000 次循環 工作溫度:-20°C ~ 70°C 其它名稱:1301.9303-ND486-1943-2 |
| FSM6JA | 功能描述:SWITCH TACTILE SPST-NO 0.05A 12V RoHS:是 類別:開關 >> 觸摸 系列:FSMJ 標準包裝:2,000 系列:LPH 電路:SPST-NO 開關功能:關-瞬時 觸點額定電壓:0.05A @ 12VDC 觸動器類型:標準 安裝類型:通孔 從引腳算起，致動器距離 PCB 的高度:7.00mm 致動器方向:頂部觸動 端接類型:PC 引腳 外形:6.00mm x 6.00mm 發光:不發光 發光電壓:- 發光類型，顏色:- 操作力:160gf 防護等級:IP40 特點:觸摸反饋 包裝:帶卷 (TR) 觸動器材料:- 開關行程:0.25mm 機械壽命:100,000 次循環 工作溫度:-20°C ~ 70°C 其它名稱:1301.9303-ND486-1943-2 |
| FSM6JAA | 制造商:MACOM 制造商全稱:Tyco Electronics 功能描述:Tactile Switches, .138 [3.5] x .236 [6], Through Hole |
| FSM6JAAH | 功能描述:觸覺開關 6MM HIGH TEMP TACT SWITCH RoHS:否 制造商:C&K Components 工作力:2 N 執行器:Round 電流額定值:50 mA 電壓額定值 DC:32 V 電壓額定值 AC: 功率額定值:1 VA 接地端子:Yes 觸點形式:SPST-NO 開關功能: 安裝風格:SMD/SMT 安裝方向:Right 晶體管管座高度: 顏色: 照明:Not Illuminated 照明顏色: 封裝: |
發布緊急采購，3分鐘左右您將得到回復。