- 您現在的位置：買賣IC網 > PDF目錄375932 > FSDM0565R (Fairchild Semiconductor Corporation) Time-Delay Relay; Contacts:SPST-NO; Time Range:0.2 sec. to 20 sec.; Timing Function:Interval One Shot; Contact Carry Current:2A; Relay Terminals:Quick Connect; Supply Voltage:120VAC PDF資料下載
參數資料
| 型號： | FSDM0565R |
| 廠商： | Fairchild Semiconductor Corporation |
| 英文描述： | Time-Delay Relay; Contacts:SPST-NO; Time Range:0.2 sec. to 20 sec.; Timing Function:Interval One Shot; Contact Carry Current:2A; Relay Terminals:Quick Connect; Supply Voltage:120VAC |
| 中文描述： | 綠色模式飛兆半導體功率開關（FPS） |
| 文件頁數： | 11/20頁 |
| 文件大小： | 262K |
| 代理商： | FSDM0565R |
FSDM0565R
11
Functional Description
1.
Startup
: In previous generations of Fairchild Power
Switches (FPS
TM
) the Vcc pin had an external start-up
resistor to the DC input voltage line. In this generation the
startup resistor is replaced by an internal high voltage current
source. At startup, an internal high voltage current source
supplies the internal bias and charges the external capacitor
(C
vcc
) that is connected to the Vcc pin as illustrated in figure
4. When Vcc reaches 12V, the FPS
TM
begins switching and
the internal high voltage current source is disabled. Then, the
FPS
TM
continues its normal switching operation and the
power is supplied from the auxiliary transformer winding
unless Vcc goes below the stop voltage of 8V.
Figure 4. Internal startup circuit
2. Feedback Control
: FSDM0565R employs current mode
control, as shown in figure 5. An opto-coupler (such as the
H11A817A) and shunt regulator (such as the KA431) are
typically used to implement the feedback network.
Comparing the feedback voltage with the voltage across the
Rsense resistor plus an offset voltage makes it possible to
control the switching duty cycle. When the reference pin
voltage of the KA431 exceeds the internal reference voltage
of 2.5V, the H11A817A LED current increases, thus pulling
down the feedback voltage and reducing the duty cycle. This
event typically happens when the input voltage is increased
or the output load is decreased.
2.1 Pulse-by-pulse current limit
: Because current mode
control is employed, the peak current through the Sense FET
is limited by the inverting input of PWM comparator (Vfb*)
as shown in figure 5. Assuming that the 0.9mA current
source flows only through the internal resistor (2.5R +R= 2.8
k
), the cathode voltage of diode D2 is about 2.5V. Since D1
is blocked when the feedback voltage (Vfb) exceeds 2.5V,
the maximum voltage of the cathode of D2 is clamped at this
voltage, thus clamping Vfb*. Therefore, the peak value of
the current through the Sense FET is limited.
2.2 Leading edge blanking (LEB)
: At the instant the
internal Sense FET is turned on, there usually exists a high
current spike through the Sense FET, caused by primary-side
capacitance and secondary-side rectifier reverse recovery.
Excessive voltage across the Rsense resistor would lead to
incorrect feedback operation in the current mode PWM
control. To counter this effect, the FPS
TM
employs a leading
edge blanking (LEB) circuit. This circuit inhibits the PWM
comparator for a short time (T
LEB
) after the Sense FET is
turned on.
Figure 5. Pulse width modulation (PWM) circuit
3. Protection Circuit
: The FSDM0565R has several self
protective functions such as over load protection (OLP),
abnormal over current protection (AOCP), over voltage
protection (OVP) and thermal shutdown (TSD). Because
these protection circuits are fully integrated into the IC
without external components, the reliability can be improved
without increasing cost. Once the fault condition occurs,
switching is terminated and the Sense FET remains off. This
causes Vcc to fall. When Vcc reaches the UVLO stop
voltage, 8V, the protection is reset and the internal high
voltage current source charges the Vcc capacitor via the Vstr
pin. When Vcc reaches the UVLO start voltage,12V, the
FPS
TM
resumes its normal operation. In this manner, the
auto-restart can alternately enable and disable the switching
of the power Sense FET until the fault condition is
eliminated (see figure 6).
8V/12V
3
Vref
Internal
Bias
Vcc
6
Vstr
I
start
Vcc good
V
DC
C
Vcc
4
OSC
Vcc
Vref
I
delay
I
FB
V
SD
R
2.5R
Gate
driver
OLP
D1
D2
+
V
fb
*
-
Vfb
KA431
C
B
Vo
H11A817A
R
sense
SenseFET
相關PDF資料 |
PDF描述 |
|---|---|
| FSDM0565RWDTU | Green Mode Fairchild Power Switch (FPS) |
| FSDM07652RWDTU | Green Mode Fairchild Power Switch (FPS) |
| FSDM101 | Green Mode Fairchild Power Switch (FPSTM) |
| FSDM1265RBWDTU | Green Mode Fairchild Power Switch (FPS) |
| FSDM1265RB | Green Mode Fairchild Power Switch (FPS) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| FSDM0565RB | 制造商:FAIRCHILD 制造商全稱:Fairchild Semiconductor 功能描述:Green Mode Fairchild Power Switch (FPS) |
| FSDM0565RB_06 | 制造商:FAIRCHILD 制造商全稱:Fairchild Semiconductor 功能描述:Green Mode Fairchild Power Switch (FPSTM) |
| FSDM0565RBI | 制造商:FAIRCHILD 制造商全稱:Fairchild Semiconductor 功能描述:Green Mode Fairchild Power Switch (FPS) |
| FSDM0565RBIWDTU | 功能描述:電源開關 IC - 配電 SMPS Power Switch Built-in Soft Start RoHS:否 制造商:Exar 輸出端數量:1 開啟電阻（最大值）:85 mOhms 開啟時間（最大值）:400 us 關閉時間（最大值）:20 us 工作電源電壓:3.2 V to 6.5 V 電源電流（最大值）: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-23-5 |
| FSDM0565RBLW | 制造商:Fairchild Semiconductor Corporation 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。