- 您現在的位置：買賣IC網 > PDF目錄375932 > FSDH0565 (Fairchild Semiconductor Corporation) Green Mode Fairchild Power Switch (FPSTM) PDF資料下載
參數資料
| 型號： | FSDH0565 |
| 廠商： | Fairchild Semiconductor Corporation |
| 英文描述： | Green Mode Fairchild Power Switch (FPSTM) |
| 中文描述： | 綠色模式飛兆功率開關（FPSTM） |
| 文件頁數： | 10/18頁 |
| 文件大?。?/td> | 391K |
| 代理商： | FSDH0565 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁當前第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁
FSD210, FSD200
10
reliability is improved without a cost increase. If either of
these thresholds are triggered, the FPS starts an auto-restart
cycle. Once the fault condition occurs, switching is termi-
nated and the Sense FET remains off. This causes Vcc to
fall. When Vcc reaches the UVLO stop voltage
(6.7V:FSD210, 6V:FSD200), the protection is reset and the
internal high voltage current source charges the Vcc capaci-
tor. When Vcc reaches the UVLO start voltage
(8.7V:FSD210,7V:FSD200), the device attempts to resume
normal operation. If the fault condition is no longer present
start up will be successful. If it is still present the cycle is
repeated (see figure 10).
Figure 9. Protection block
4.1 Over Load Protection (OLP) :
Over load protection
occurs when the load current exceeds a pre-set level due to
an abnormal situation. If this occurs, the protection circuit
should be triggered to protect the SMPS. It is possible that a
short term load transient can occur under normal operation.
In order to avoid false shutdowns, the over load protection
circuit is designed to trigger after a delay. Therefore the
device can differentiate between transient over loads and
true fault conditions. The maximum input power is limited
using the pulse-by-pulse current limit feature. If the load
tries to
draw more than this, the output voltage will drop below its
set value. This reduces the optocoupler LED current which
in turn reduces the photo-transistor current (see figure 9).
Therefore, the 250uA current source will charge the feed-
back pin capacitor, Cfb, and the feedback voltage, Vfb, will
increase. The input to the feedback comparator is clamped at
3V. Once Vfb reaches 3V, the device switches at maximum
power, the 250uA current source is blocked and the 5uA
source continues to charge Cfb. Once Vfb reaches 4V,
switching stops.and overload protection is triggered. The
resultant shutdown delay time is set by the time required to
charge Cfb from 3Vto 4Vwith 5uA as shown in Fig. 10.
4.2 Thermal Shutdown (TSD) :
The Sense FET and the
control IC are integrated, making it easier for the control IC
to detect the temperature of the Sense FET. When the tem-
perature exceeds approximately 145°C, thermal shutdown is
activated.
Figure 10. Over load protection delay
5. Soft Start :
FSD200/210 has an internal soft start circuit
that gradually increases current through the Sense FET as
shown in figure 11. The soft start time is 3msec in FSD200/
210.
Figure 11. Internal Soft Start
6. Burst operation :
In order to minimize the power dissipa-
tion in standby mode, the FSD200/210 implements burst
mode functionality (see figure 12). As the load decreases, the
feedback voltage decreases. As shown in figure 13, the
device automatically enters burst mode when the feedback
voltage drops below V
BURL
(0.58V). At this point switching
stops and the output voltages start to drop at a rate dependant
on standby current load. This causes the feedback voltage to
rise. Once it passes V
BURH
(0.64V) switching starts again.
The feedback voltage falls and the process repeats. Burst
mode operation alternately enables and disables switching of
the power Sense FET thereby reducing switching loss in
OSC
4
Vfb
S
R
Q
GATE
DRIVER
FSD2xx
OLP, TSD
Protection Block
5uA
250uA
RESET
Vth 4V
OLP
+
-
TSD
S
R
Q
A/R
Cfb
3V
R
Vfb
t
3V
OLP
4V
t1
t3
t1<<t2, t3
t1 = -1/RC
t2 = Cfb
Χ
ln( 1-v(t1)/R )
Χ
{v(t1+t2)-v(t1)}
v(t1)=3V
/
/
/
/
Idelay
t2
FPS Switching Area
Idelay (5uA) charges Cfb
IC Reset
under Vstop of UVLO
0.2A
0.25A
0.3A
3mS
Iover
FSD200/210
I(A)
t
相關PDF資料 |
PDF描述 |
|---|---|
| FSD200 | Green Mode Fairchild Power Switch (FPSTM) |
| FSD200M | Green Mode Fairchild Power Switch (FPSTM) |
| FSD210M | Green Mode Fairchild Power Switch (FPSTM) |
| FSD210 | Green Mode Fairchild Power Switch (FPSTM) |
| FSDH565 | Fairchild Power Switch(FPS) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| FSDH321 | 功能描述:電源開關 IC - 配電 FPS for DVDP/STB RoHS:否 制造商:Exar 輸出端數量:1 開啟電阻（最大值）:85 mOhms 開啟時間（最大值）:400 us 關閉時間（最大值）:20 us 工作電源電壓:3.2 V to 6.5 V 電源電流（最大值）: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-23-5 |
| FSDH321_04 | 制造商:FAIRCHILD 制造商全稱:Fairchild Semiconductor 功能描述:Green Mode Fairchild Power Switch |
| FSDH321L | 功能描述:電源開關 IC - 配電 FPS for DVDP/STB RoHS:否 制造商:Exar 輸出端數量:1 開啟電阻（最大值）:85 mOhms 開啟時間（最大值）:400 us 關閉時間（最大值）:20 us 工作電源電壓:3.2 V to 6.5 V 電源電流（最大值）: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-23-5 |
| FSDH321LX | 制造商:Fairchild Semiconductor Corporation 功能描述:Power Switch 2A 8-Pin LSOP |
| FSDH321Z | 功能描述:IC SWIT PWM GREEN CM OVP HV 8DIP RoHS:是 類別:集成電路 (IC) >> PMIC - AC-DC 轉換器，離線開關 系列:- 標準包裝:1 系列:FPS™ 輸出隔離:隔離 頻率范圍:61kHz ~ 73kHz 輸入電壓:8 V ~ 26 V 輸出電壓:650V 功率（瓦特）:12W 工作溫度:-40°C ~ 115°C 封裝/外殼:8-DIP（0.300"，7.62mm） 供應商設備封裝:8-MDIP 包裝:Digi-Reel® 其它名稱:FSL206MRBNFSDKR |
發布緊急采購，3分鐘左右您將得到回復。