- 您現在的位置：買賣IC網 > PDF目錄375931 > FSDH0265RL (FAIRCHILD SEMICONDUCTOR CORP) Green Mode Fairchild Power Switch (FPSTM) PDF資料下載
參數資料
| 型號： | FSDH0265RL |
| 廠商： | FAIRCHILD SEMICONDUCTOR CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | Green Mode Fairchild Power Switch (FPSTM) |
| 中文描述： | 8 A SWITCHING REGULATOR, 108 kHz SWITCHING FREQ-MAX, PDSO8 |
| 封裝： | SOP-8 |
| 文件頁數： | 10/20頁 |
| 文件大?。?/td> | 479K |
| 代理商： | FSDH0265RL |
FSDL0165RN
10
Functional Description
1. Startup
: In previous generations of Fairchild Power
Switches (FPS
TM
) the Vstr pin had an external resistor to the
DC input voltage line. In this generation the startup resistor
is replaced by an internal high voltage current source and a
switch that shuts off when 15mS goes by after the supply
voltage, Vcc, gets above 12V. The source turns back on if
Vcc drops below 8V.
Figure 4. High voltage current source
2. Feedback Control
:
The FSDL0165RN employs current
mode control, shown in figure 5. An opto-coupler (such as
the H11A817A) and shunt regulator (such as the KA431) are
typically used to implement the feedback network. Compar-
ing the feedback voltage with the voltage across the Rsense
resistor plus an offset voltage makes it possible to control the
switching duty cycle. When the reference pin voltage of the
KA431 exceeds the internal reference voltage of 2.5V, the
H11A817A LED current increases, thus pulling down the
feedback voltage and reducing the duty cycle. This event
typically happens when the input voltage is increased or the
output load is decreased.
3. Leading edge blanking (LEB)
:
At the instant the internal
Sense FET is turned on, there usually exists a high current
spike through the Sense FET, caused by the primary side
capacitance and secondary side rectifier diode reverse recov-
ery. Excessive voltage across the Rsense resistor would lead
to incorrect feedback operation in the current mode PWM
control. To counter this effect, the FPS
TM
employs a leading
edge blanking (LEB) circuit. This circuit inhibits the PWM
comparator for a short time (T
LEB
) after the Sense FET is
turned on.
Figure 5. Pulse width modulation (PWM) circuit
4. Protection Circuit
:
The FPS
TM
has several protective
func-
tions such as over load protection (OLP), over voltage pro-
tection (OVP), abnormal over current protection (AOCP),
under voltage lock out (UVLO) and thermal shutdown
(TSD). Because these protection circuits are fully integrated
inside the IC without external components, the reliability is
improved without increasing cost. Once the fault condition
occurs, switching is terminated and the Sense FET remains
off. This causes Vcc to fall. When Vcc reaches the UVLO
stop voltage, 8V, the protection is reset and the internal high
voltage current source charges the Vcc capacitor via the Vstr
pin. When Vcc reaches the UVLO start voltage,12V, the
FPS
TM
resumes its normal operation. In this manner, the
auto-restart can alternately enable and disable the switching
of the power Sense FET until the fault condition is elimi-
nated.
4.1 Over Load Protection (OLP)
:
Overload is defined
as the
load current exceeding a pre-set level due to an unexpected
event. In this situation, the protection circuit should be acti-
vated in order to protect the SMPS. However, even when the
SMPS is in the normal operation, the over load protection
circuit can be activated during the load transition. In order to
avoid this undesired operation, the over load protection cir-
cuit is designed to be activated after a specified time to deter-
mine whether it is a transient situation or an overload
situation. In conjunction with the Ipk current limit pin (if
used) the current mode feedback path would limit the current
in the Sense FET when the maximum PWM duty cycle is
attained. If the output consumes more than this maximum
power, the output voltage (Vo) decreases below the set volt-
age. This reduces the current through the opto-coupler LED,
which also reduces the opto-coupler
transistor current, thus
increasing the feedback voltage (Vfb). If Vfb exceeds 3V, the feed-
back input diode is blocked and the 5uA I
delay
current source starts
to charge Cfb slowly up to Vcc. In this condition, Vfb continues
increasing until it reaches 6V, when the switching operation is ter-
minated as shown in figure 6. The delay time for shutdown is the
time required to charge Cfb from 3V to 6V with 5uA.
Vin,dc
Vstr
Vcc
15mS After UVLO
start(>12V)
off
UVLO <8V
on
Istr
J-FET
3
OSC
Vcc
Vref
2uA
0.9mA
V
SD
R
28R
FB
Gate
driver
OLP
D1
D2
Vfb*
Vfb
431
Cfb
Vo
相關PDF資料 |
PDF描述 |
|---|---|
| FSDH0265RN | Green Mode Fairchild Power Switch (FPSTM) |
| FSDH321 | Green Mode Fairchild Power Switch (FPSTM) |
| FSDH321L | Green Mode Fairchild Power Switch (FPS TM) |
| FSDL0165RL | Green Mode Fairchild Power Switch (FPSTM) |
| FSDL0165RN | Green Mode Fairchild Power Switch (FPSTM) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| FSDH0265RLX | 功能描述:電源開關 IC - 配電 SMPS PwrSwtch 100kHz 20W for DVDP/STB RoHS:否 制造商:Exar 輸出端數量:1 開啟電阻（最大值）:85 mOhms 開啟時間（最大值）:400 us 關閉時間（最大值）:20 us 工作電源電壓:3.2 V to 6.5 V 電源電流（最大值）: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-23-5 |
| FSDH0265RN | 功能描述:電源開關 IC - 配電 SMPS Power Switch 100kHz 20W for RoHS:否 制造商:Exar 輸出端數量:1 開啟電阻（最大值）:85 mOhms 開啟時間（最大值）:400 us 關閉時間（最大值）:20 us 工作電源電壓:3.2 V to 6.5 V 電源電流（最大值）: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-23-5 |
| FSDH0265RN_05 | 制造商:FAIRCHILD 制造商全稱:Fairchild Semiconductor 功能描述:Green Mode Fairchild Power Switch (FPSTM) |
| FSDH0270RNB | 功能描述:電源開關 IC - 配電 FPS FOR DVDP/STB RoHS:否 制造商:Exar 輸出端數量:1 開啟電阻（最大值）:85 mOhms 開啟時間（最大值）:400 us 關閉時間（最大值）:20 us 工作電源電壓:3.2 V to 6.5 V 電源電流（最大值）: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-23-5 |
| FSDH0370RNB | 功能描述:電源開關 IC - 配電 FPS FOR DVDP/STB RoHS:否 制造商:Exar 輸出端數量:1 開啟電阻（最大值）:85 mOhms 開啟時間（最大值）:400 us 關閉時間（最大值）:20 us 工作電源電壓:3.2 V to 6.5 V 電源電流（最大值）: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-23-5 |
發布緊急采購，3分鐘左右您將得到回復。