- 您現在的位置：買賣IC網 > PDF目錄371743 > FSCT FAN SPEED CONTROLER PDF資料下載
參數資料
| 型號： | FSCT |
| 英文描述： | FAN SPEED CONTROLER |
| 中文描述： | 風扇轉速智能控制器 |
| 文件頁數： | 6/11頁 |
| 文件大?。?/td> | 114K |
| 代理商： | FSCT |
FSCTxxA-UH5
6/11
2. Hysteresis control (mode OFF)
FSCT can be shut down by the ON signal. When, this signal is low, the OUT pin is at high level, i.e. the FAN
is turned off.
This mode enables to save the energy wasted by the FAN in case of operations at very low output power.
For a 12 V supply voltage, the shut-down of the FAN brings a 0.5 to 2.5 W power saving (for a 200 mA 12 V
DC motor).
During the mode OFF, the FSCT doesn't lose temperature control; indeed, in case of over-temperature,
the FAN is automatically switched on. This safety feature protects the power supply or the semiconductor
devices from unexpected over-temperature.
In order to keep the energy saving benefit, the FSCT turns back off the FAN when the temperature falls be-
low T
OFF
threshold.
In practice, three cases can appear for a constant applied heating power (for instance, the output power of
the power supply where the FSCT is used) (cf. figure 8):
I
Case 1:
the heating power is too low, and keeps T
j
below T
ON
. The FAN remains OFF.
I
Case 2:
the heating power is high enough to raise T
j
above T
ON
. But, as this power is quite low, T
j
falls
down T
OFF
, and the temperature starts again to increase, up to T
ON
. This results in a FAN ON/OFF pe-
riodical cycle.
I
Case 3:
the heating power is higher that in case 2, so that Tj remains above T
OFF
. The FAN stays ON
in that case, unless the heating power decreases.
For example, with a 200 W computer power supply, working with a FSCT17 device put on the power semi-
conductors heatsink, Case 1 could be reached for a 25 W output power consumption (T
j
will stabilize
around 60 °C, i.e. below typical T
ON
).
Case 2 could be reached for a 50 W power consumption. Then, thanks to the large Hysteresis value (30 °C
typ.), the ON/OFF period (refer to T
P
on figure 8) lasts approximately 15 minutes. This is long enough to
avoid too many FAN starts-up cycle per hour.
Case 3 could be reached for a 75W, or higher, power consumption. For 75W, the power supply ambient
temperature stabilizes itself around 42°C.
Itshouldbenotedthat,forCase3,suchsteadystatepointsofoperation,areallowedduetothefactthatthe
OUT voltage follows the same linear law as that in ON mode. Then, the Hysteresis control is smarter than a
simple ON/OFF control mode.
Mode OFF
Mode ON
V
OUT
V
CC
1V
V
OL
T (°C)
j
V
OMS
T
OL
T
ON
T
OFF
T
MS
Fig. 7:
OUT voltage versus junction temperature.
相關PDF資料 |
PDF描述 |
|---|---|
| FSDM-10 | Delay Line |
| FSDM-100 | Delay Line |
| FSDM-1000 | Delay Line |
| FSDM-125 | Delay Line |
| FSDM3-1000M | Delay Line |
相關代理商/技術參數 |
參數描述 |
|---|---|
| FSCT07A-UH5 | 功能描述:馬達/運動/點火控制器和驅動器 Fan Speed Controller RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| FSCT11A-UH5 | 功能描述:馬達/運動/點火控制器和驅動器 Fan Speed Controller RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| FSCT17A-UH5 | 功能描述:馬達/運動/點火控制器和驅動器 Fan Speed Controller RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| FSCTEST | 制造商:Fairchild Semiconductor Corporation 功能描述:. |
| FSCTXXA-UH5 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:FAN SPEED CONTROLER |
發布緊急采購，3分鐘左右您將得到回復。