參數資料
型號： FSCQ
廠商： Fairchild Semiconductor Corporation
英文描述： Green Mode Fairchild Power Switch (FPS)
中文描述： 綠色模式飛兆半導體功率開關（FPS）
文件頁數： 17/44頁
文件大?。?/td> 1204K
代理商： FSCQ
FSCQ-SERIES
17
preset maximum current to be supplied to the SMPS until the
over load protection triggers. Because more energy than
required is provided to the output, the output voltage may
exceed the rated voltage before the over load protection
triggers, resulting in the breakdown of the devices in the
secondary side. In order to prevent this situation, an over
voltage protection (OVP) circuit is employed. In general, the
peak voltage of the sync signal is proportional to the output
voltage and the FSCQ-Series uses a sync signal instead of
directly monitoring the output voltage. If the sync signal
exceeds 12V, an OVP is triggered resulting in a shutdown of
SMPS. In order to avoid undesired triggering of OVP during
normal operation, the peak voltage of the sync signal should
be designed to be below 12V. This protection is implemented
in the auto restart mode.
4.4 Thermal Shutdown (TSD) :
The SenseFET and the
control IC are built in one package. This makes it easy for
the control IC to detect abnormal over temperature of the
SenseFET. When the temperature exceeds approximately
150
°
C, the thermal shutdown triggers. This protection is
implemented in the latch mode.
5. Soft Start
: The FSCQ-Series has an internal soft-start
circuit that increases PWM comparator’s inverting input
voltage together with the SenseFET current slowly after it
starts up. The typical soft start time is 20msec. The pulse
width to the power switching device is progressively
increased to establish the correct working conditions for
transformers, inductors, and capacitors. Increasing the pulse
width to the power switching device also helps prevent
transformer saturation and reduces the stress on the
secondary diode during startup. For a fast build up of the
output voltage, an offset is introduced in the soft-start
reference current.
6. Burst Operation :
In order to minimize the power
consumption in the standby mode, the FSCQ-Series employs
burst operation. Once FSCQ-Series enters into the burst
mode, FSCQ-Series allows all output voltages and effective
switching frequency to be reduced. Figure 15 shows the
typical feedback circuit for C-TV applications. In normal
operation, the picture on signal is applied and the transistor
Q
1
is turned on, which de-couples R
3
, D
z
and D1 from the
feedback network. Therefore, only V
o1
is regulated by the
feedback circuit in normal operation and determined by R
1
and R
2
as
In the standby mode, the picture ON signal is disabled and
the transistor Q
1
is turned off, which couples R
3
, Dz, and D
1
to the reference pin of KA431. Then, Vo2 is determined by
the zener diode breakdown voltage. Assuming that the
forward voltage drop of D
1
is 0.7V, V
o2
in standby mode is
approximately given by
Figure 15. Typical Feedback Circuit to Drop Output Volt-
age in Standby Mode
Figure 17 shows the burst mode operation waveforms. When
the picture ON signal is disabled, Q
1
is turned off and R
3
and Dz are connected to the reference pin of KA431 through
D
1
. Before V
o2
drops to V
o2
stby
, the voltage on the reference
pin of KA431 is higher than 2.5V, which increases the
current through the opto LED. This pulls down the feedback
voltage (V
FB
) of FSCQ-Series and forces FSCQ-Series to
stop switching. If the switching is disabled longer than
1.4ms, FSCQ-Series enters into burst operation and the
operating current is reduced from I
OP
to 0.25mA (I
OB
). Since
there is no switching, V
o2
decreases until it reaches V
o2
stby
.
As V
o2
reaches V
o2
stby
, the current through the opto LED
decreases allowing the feedback voltage to rise. When the
feedback voltage reaches 0.4V, FSCQ-Series resumes
switching with a predetermined peak drain current of 0.9A.
After burst switching for 1.4ms, FSCQ-Series stops
switching and checks the feedback voltage. If the feedback
voltage is below 0.4V, FSCQ-Series stops switching until the
feedback voltage increases to 0.4V. If the feedback voltage is
above 0.4V, FSCQ-Series goes back to the normal operation.
The output voltage drop circuit can be implemented
alternatively as shown in Figure 16. In the circuit of Figure
16, the FSCQ-Series goes into burst mode, when picture off
signal is applied to Q1. Then, Vo2 is determined by the zener
diode breakdown voltage. Assuming that the forward
V
o1
norm
2.5
R
--------------------
R
2
+
R
2
=
V
o2
stby
V
Z
0.7
2.5
+
+
=
Picture ON
Micom
Linear
Regulator
V
O2
V
O1
(B+)
KA431
R
2
R
1
R
3
R
bias
R
D
R
F
C
F
D
1
Q1
A
C
R
Dz
相關PDF資料
PDF描述
FSCQ1465RT Green Mode Fairchild Power Switch (FPS)
FSCQ1565RP Green Mode Fairchild Power Switch (FPS) for Quasi-Resonant Switching Converter
FSCQ1565RPSYDTU Green Mode Fairchild Power Switch (FPS) for Quasi-Resonant Switching Converter
FSCQ0965RTYDTU Green Mode Fairchild Power Switch (FPS)
FSCQ1465RTYDTU Green Mode Fairchild Power Switch (FPS)
相關代理商/技術參數
參數描述
FSCQ_06 制造商:FAIRCHILD 制造商全稱:Fairchild Semiconductor 功能描述:Green Mode Fairchild Power Switch (FPS⑩)
FSCQ0565RT 制造商:FAIRCHILD 制造商全稱:Fairchild Semiconductor 功能描述:Green Mode Fairchild Power Switch (FPS)
FSCQ0565RTYDTU 功能描述:電源開關 IC - 配電 5A 650V QRC PwrSwtch RoHS:否 制造商:Exar 輸出端數量:1 開啟電阻（最大值）:85 mOhms 開啟時間（最大值）:400 us 關閉時間（最大值）:20 us 工作電源電壓:3.2 V to 6.5 V 電源電流（最大值）: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-23-5
FSCQ0765RT 制造商:FAIRCHILD 制造商全稱:Fairchild Semiconductor 功能描述:Green Mode Fairchild Power Switch (FPS)
FSCQ0765RTYDTU 功能描述:軟開關 PWM 控制器 7A/650V QRC Power Switch RoHS:否 制造商:Fairchild Semiconductor 輸出端數量: 輸出電流: 開關頻率: 工作電源電壓:30 V 電源電流: 最大工作溫度:+ 105 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*