- 您現在的位置：買賣IC網 > PDF目錄375926 > FS8S0965RCBYDTU (FAIRCHILD SEMICONDUCTOR CORP) Fairchild Power Switch(FPS) PDF資料下載
參數資料
| 型號： | FS8S0965RCBYDTU |
| 廠商： | FAIRCHILD SEMICONDUCTOR CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | Fairchild Power Switch(FPS) |
| 中文描述： | 32.4 A SWITCHING REGULATOR, 150 kHz SWITCHING FREQ-MAX, PZFM5 |
| 封裝： | TO-220, 5 PIN |
| 文件頁數： | 11/20頁 |
| 文件大?。?/td> | 2039K |
| 代理商： | FS8S0965RCBYDTU |
FS8S0965RCB
11
Functional Description
1.
Start up
: To guarantee stable operation of the
control IC, FS8S0965RCB has UVLO circuit with 6V
hysteresis band. Figure 1 shows the relation between the sup-
ply current (Icc) and the supply voltage (Vcc). Before Vcc
reaches 15V, the FPS consumes only startup current of
80
μ
A, which is usually provided by the DC link through
start-up resistor. When Vcc reaches 15V, the FPS begins
operation and the operating current increases to 15mA as
shown. Once the control IC starts operation, it continues its
normal operation until Vcc goes below the stop voltage of
9V
Figure 1. Strat up with hysteresis
2. Feedback Control
: FS8S0965RCB employs primary side
regulation, which permits elimination of feedback circuit
components in the secondary side such as opto coupler and
TL431. Figure 2 shows the primary side control circuit. The
primary side regulation voltage (Vpsr) is controlled to the
breakdown voltage of zener diode (Dz). Because current
mode control is employed, the drain current of the power
MOSFET is limited by the inverting input of PWM compara-
tor (Vfb*). When MOSFET turns on, usually there exists
high current spike in the MOSFET current caused by pri-
mary-side capacitance and secondary-side rectifier reverse
recovery. In order to prevent premature termination of the
switching pulse due to the current spike, the FPS employs
leading edge blanking (LEB). The leading edge blanking cir-
cuit inhibits the PWM comparator for a short time after the
MOSFET is turned on.
Figure 2. Primary side control circuit
3. Protection function
: FS8S0965RCB has 4 self
protective functions such as abnormal over current protec-
tion (AOCP), over load protection (OLP), over voltage pro-
tection (OVP) and thermal shutdown (TSD). Because these
protection circuits are fully integrated into the IC without
external components, the reliability can be improved without
cost increase. In the event of these fault conditions, the FPS
enters into auto-restart operation. Once the fault condition
occurs, switching operation is terminated and MOSFET
remains off, which forces Vcc to be reduced. When Vcc
reaches 9V, the protection is reset and the supply current
reduces to 80 uA. Then, Vcc begin to increase with the cur-
rent provided through the start-up resistor. When Vcc
reaches 15V, the FPS resumes its normal operation if the
fault condition is removed. In this manner, the auto-restart
alternately enables and disables the switching of the power
MOSFET until the fault condition is eliminated as illustrated
in figure 3.
Figure 3. Auto restart operation after protection
3.1 Abnormal Over Current Protection (AOCP)
: When
the secondary rectifying diodes or the transformer pins are
shorted, a steep current with extremely high di/dt can flow
during the LEB time. Therefore, the abnormal over current
protection (AOCP) block is added to ensure the reliability as
shown in figure 4. It turns off the SenseFET within 300ns
after the abnormal over current condition is sensed.
Figure 4. AOCP block
Vstop=9V
Vstart=15V
80uA
OVP
Vcc
Icc
15mA
4
OSC
Vcc
Vref
2uA
0.9mA
V
SD
R
2.5R
FB
Gate
driver
OLP
D1
D2
Vfb*
Vfb
Cfb
D
Z
R
Z
V
psr
time
time
V
V
15V
9 V
Vcc
Vds
Protection is activated
(OCP,OLP,OVP or TSD)
Auto restart
V c c
GATE
DRIVER
AOCP COMP.
Vsense : 1V
SenseFET
S Q'
R
OVP
OLP
TSD
UVLO
PWMComp
相關PDF資料 |
PDF描述 |
|---|---|
| FSA1156 | Low RON Low Voltage SPST Analog Switch |
| FSA1156L6X | Low RON Low Voltage SPST Analog Switch |
| FSA1156P6 | Low RON Low Voltage SPST Analog Switch |
| FSA1156P6X | Low RON Low Voltage SPST Analog Switch |
| FSA1157 | Low RON Low Voltage SPST Analog Switch |
相關代理商/技術參數 |
參數描述 |
|---|---|
| FS-90/1 | 制造商:Measurement Specialties Inc 功能描述:SENSOR LIQUID FLOW 3L/MIN COPPER 制造商:Measurement Specialties Inc 功能描述:SENSOR, LIQUID FLOW, 3L/MIN, COPPER 制造商:Measurement Specialties Inc 功能描述:SENSOR, LIQUID FLOW, 3L/MIN, COPPER, Port Size:15mm, SVHC:No SVHC (20-Jun-2013) |
| FS900020793 | 制造商:3M Electronic Products Division 功能描述:PREFORM SEALNT STRIP 5M |
| FS-9003 | 功能描述:開發板和工具包 - ARM JTAG Booster PC Intel 386EX 3.3V RoHS:否 制造商:Arduino 產品:Development Boards 工具用于評估:ATSAM3X8EA-AU 核心:ARM Cortex M3 接口類型:DAC, ICSP, JTAG, UART, USB 工作電源電壓:3.3 V |
| FS-9005 | 功能描述:插座和適配器 JTAG Booster PC ARM7TDMI 3.3V RoHS:否 制造商:Silicon Labs 產品:Adapter 用于:EM35x |
| FS-9007 | 功能描述:開發板和工具包 - ARM Core 7U Biometric Kit IKENDI RoHS:否 制造商:Arduino 產品:Development Boards 工具用于評估:ATSAM3X8EA-AU 核心:ARM Cortex M3 接口類型:DAC, ICSP, JTAG, UART, USB 工作電源電壓:3.3 V |
發布緊急采購，3分鐘左右您將得到回復。