•
      參數資料
      型號： FS1601-7PD5
      元件分類： 電源模塊
      英文描述： 1-OUTPUT 100 W DC-DC REG PWR SUPPLY MODULE
      封裝： HEAT SINK, METAL, CASE S02, MODULE
      文件頁數： 19/31頁
      文件大?。?/td> 633K
      代理商： FS1601-7PD5
      Cassette Style
      100 Watt DC-DC Converters
      S Series
      Edition 1/01.2000
      26/31
      Fig. 28
      Paralleling of single output units using option T with the
      sense lines connected at the load
      1 Leads should have equal length and cross sections and should
      run in the same cable loom.
      2 Diodes recommended in redundant operation only
      3 DC common point
      Load
      1
      2
      3
      S+
      Vo+
      Vo–
      S–
      Vi+
      Vi–
      T
      Vi+
      Vi–
      S+
      Vo+
      Vo–
      S–
      T
      1
      max. 5 units in parallel connection
      11036
      Load
      max. 5 units in parallel connection
      +
      –
      Power bus
      Module
      Vo2–
      Vo2+
      Vo1–
      Vo1+
      T
      Module
      Vo2–
      Vo2+
      Vo1–
      Vo1+
      T
      11037
      Fig. 29
      Paralleling of double output units using option T (e.g.
      Powerbus)
      Vo+
      Vo–
      Vo+
      Vo–
      Load
      Vo+
      Vo–
      11003
      Fig. 27
      An example of poor wiring for connection in parallel
      T Current Sharing
      This option ensures that the output currents are approxi-
      mately shared between all paralleled modules, hence in-
      creasing system reliability. To use this facility, simply inter-
      connect the T pins of all modules and make sure, that pins
      14, the S– pins (S 1000) or the Vo1– pins (S 2000) are also
      connected together. The load leads should have equal
      length and cross section to ensure equal voltage drops. Not
      more than 5 units should be connected in parallel.
      Note: If output voltage adjustment is requested we strongly
      recommend to use the R-input instead of option P, as with
      option P the required setting accuracy is difficult to achieve.
      The output voltages must be individually set prior to paral-
      leling to within a tolerance of 1...2% or the R pins should be
      connected together.
      P Potentiometer
      The potentiometer provides an output voltage adjustment
      range of +10/–60% of
      Uo nom and is accessible through a
      hole in the front cover. This feature enables compensation
      of voltage drops across the connector and wiring. Option P
      is not recommended if units are connected in parallel.
      Option P excludes the R-function. With double output units
      both outputs are affected by the potentiometer setting (dou-
      bling the voltage setting if the outputs are in series).
      If the output voltages are increased above
      Uo nom via R-in-
      put control, option P setting, remote sensing or option T, the
      output current(s) should be reduced accordingly so that
      Po nom is not exceeded.
      D Undervoltage Monitor
      The input and/or output undervoltage monitoring circuit op-
      erates independently of the built-in input undervoltage lock-
      out circuit. A logic "low" (JFET output) or "high" signal (NPN
      output) is generated at pin 20 as soon as one of the moni-
      tored voltages drops below the preselected threshold level
      Ut. The return for this signal is Vo1–. The D output recovers
      when the monitored voltage(s) exceed(s)
      Ut + Uh. The
      threshold levels
      Uti and Uto are either adjustable by a poten-
      tiometer, accessible through a hole in the front cover, or fac-
      tory adjusted to a fixed value specified by the customer.
      Option D exists in various versions D0...DD as shown in the
      following table.
      相關PDF資料
      PDF描述
      FS1601-7RD4T 1-OUTPUT 100 W DC-DC REG PWR SUPPLY MODULE
      FS1601-9EPD8B2 1-OUTPUT 100 W DC-DC REG PWR SUPPLY MODULE
      FS1601-9PD3B1 1-OUTPUT 100 W DC-DC REG PWR SUPPLY MODULE
      FS2320-7EPD8TB1 2-OUTPUT 100 W DC-DC REG PWR SUPPLY MODULE
      FS2320-7ERDDB1 2-OUTPUT 100 W DC-DC REG PWR SUPPLY MODULE
      相關代理商/技術參數
      參數描述
      FS1601-7R 功能描述:EURO-CASSETTE 100W 24V RoHS:否 類別:電源 - 外部/內部（非板載） >> DC DC Converters 系列:* 標準包裝:1 系列:Quint 類型:隔離 輸入電壓:24V 輸出:24V 輸出數:1 輸出 - 1 @ 電流（最大）:24 VDC @ 50A 輸出 - 2 @ 電流（最大）:- 輸出 - 3 @ 電流（最大）:- 輸出 - 4 @ 電流（最大）:- 功率（瓦特）:1200W 安裝類型:底座安裝 工作溫度:0°C ~ 40°C 效率:- 封裝/外殼:模塊 尺寸/尺寸:4.33" L x 9.09" W x 6.14" H（110mm x 231mm x 156mm） 包裝:散裝 電源（瓦特）- 最大:1200W 批準:- 其它名稱:277-69722866365-NDQUINT-BAT/24DC/12AH
      FS1601-9ER 制造商:Power-One 功能描述:DCDC - Bulk
      FS16-070 功能描述:電源變壓器 1.1VA 16.0VCT@0.07A DUAL PRIMARY RoHS:否 制造商:Triad Magnetics 功率額定值:12 VA 初級電壓額定值:115 V / 230 V 次級電壓額定值:12 V / 24 V 安裝風格:SMD/SMT 一次繞組:Dual Primary Winding 二次繞組:Dual Secondary Winding 長度:2.5 in 寬度:2 in 高度:1.062 in
      FS16-070-C2 功能描述:電源變壓器 1.1VA 16.0VCT@0.07A Dual Primary Class 2 RoHS:否 制造商:Triad Magnetics 功率額定值:12 VA 初級電壓額定值:115 V / 230 V 次級電壓額定值:12 V / 24 V 安裝風格:SMD/SMT 一次繞組:Dual Primary Winding 二次繞組:Dual Secondary Winding 長度:2.5 in 寬度:2 in 高度:1.062 in
      FS16-070-C2-B 制造商:Triad Magnetics 功能描述:XFRMR LAMINATED 1.1VA THRU HOLE
      發布緊急采購，3分鐘左右您將得到回復。

      采購需求

      (若只采購一條型號，填寫一行即可)

      發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

      發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

      *型號 *數量 廠商 批號 封裝
      添加更多采購

      我的聯系方式

      *
      *
      *