- 您現在的位置：買賣IC網 > PDF目錄67586 > FS1501-9EPD8B1 1-OUTPUT 100 W DC-DC REG PWR SUPPLY MODULE PDF資料下載
參數資料
| 型號： | FS1501-9EPD8B1 |
| 元件分類： | 電源模塊 |
| 英文描述： | 1-OUTPUT 100 W DC-DC REG PWR SUPPLY MODULE |
| 封裝： | METAL, CASE S02, MODULE |
| 文件頁數： | 4/31頁 |
| 文件大小： | 633K |
| 代理商： | FS1501-9EPD8B1 |
第1頁第2頁第3頁當前第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁
Cassette Style
100 Watt DC-DC Converters
S Series
Edition 1/01.2000
12/31
Thermal Considerations
If a converter is located in free, quasi-stationary air (con-
vection cooling) at the indicated maximum ambient tem-
perature
TA max (see table: Temperature specifications) and
is operated at its nominal input voltage and output power,
the temperature measured at the
Measuring point of case
temperature TC (see: Mechanical Data) will approach the
indicated value
TC max after the warm-up phase. However,
the relationship between
TA and TC depends heavily on the
conditions of operation and integration into a system. The
thermal conditions are influenced by input voltage, output
current, airflow and temperature of surrounding compo-
nents and surfaces.
TA max is therefore, contrary to TC max,
an indicative value only.
Caution: The installer must ensure that under all operat-
ing conditions
TC remains within the limits stated in the
table:
Temperature specifications.
Notes: Sufficient forced cooling or an additional heat sink
allows
TA to be higher than 71
°C (e.g. 85°C) if T
C max is not
exceeded.
For -7 or -9 units at an ambient temperature
TA of 85
°C with
only convection cooling, the maximum permissible current
for each output is approx. 40% of its nominal value as per
figure.
0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
50
60
70
80
90
100
Io/Io nom
TA [°C]
0.9
1.0
Forced cooling
05089
TA min
TC max
Convection cooling
Fig. 7
Output current derating versus temperature for -7 and -9
units.
Thermal Protection
A temperature sensor generates an internal inhibit signal
which disables the outputs if the case temperature exceeds
TC max. The outputs are automatically re-enabled if the tem-
perature drops below this limit.
It is recommended that continuous operation under simul-
taneous extreme worst case conditions of the following
three parameters be avoided: Minimum input voltage,
maximum output power and maximum temperature.
Output Protection
Each output is protected against overvoltage which could
occur due to a failure of the control circuit by means of a
voltage suppressor diode which, under worst case condi-
tions, may become a short circuit. The suppressor diodes
are not designed to withstand externally applied over-
voltages. Overload at any of the two outputs will cause a
shut-down of both outputs. A red LED indicates the over-
load condition.
Output Voltage Regulation of Single or Double Output
Modules with Outputs 1 and 2 Connected in Series
Uo
Uo nom
0.98
0.5
0
0.5
1.0
Io1
IoL
Io
Io nom
05068
Fig.8
Uo1 vs. Io1 (typ.) of single output units
Parallel or Series Connection of Units
Single or double output units with equal nominal output volt-
age can be connected in parallel without any precautions
using option T.
With option T (current sharing), all units share the current
approximately equally.
Single output units and/or main and second outputs of dou-
ble output units can be connected in series with any other
(similar) output.
Note: Parallel connection of double output units should al-
ways include both, main and second output to maintain
good regulation of both outputs.
Not more than 5 units should be connected in parallel.
Series connection of second outputs without involving their
main outputs should be avoided as regulation may be poor.
The maximum output current is limited by the output with
the lowest current limitation if several outputs are con-
nected in series.
相關PDF資料 |
PDF描述 |
|---|---|
| FS1601-7EPD6TB1 | 1-OUTPUT 100 W DC-DC REG PWR SUPPLY MODULE |
| FS1601-7EPD8T | 1-OUTPUT 100 W DC-DC REG PWR SUPPLY MODULE |
| FS1601-7EPD9TB2 | 1-OUTPUT 100 W DC-DC REG PWR SUPPLY MODULE |
| FS1601-7EPDDTB1 | 1-OUTPUT 100 W DC-DC REG PWR SUPPLY MODULE |
| FS1601-7ERD3TB1 | 1-OUTPUT 100 W DC-DC REG PWR SUPPLY MODULE |
相關代理商/技術參數 |
參數描述 |
|---|---|
| FS1501-9ER | 制造商:Power-One 功能描述:DCDC - Bulk |
| FS150-20 | 制造商:JAMECO VALUEPRO 功能描述:Test Leads Breadboard 20 Pack 5.9 Inch (150mm) Wire Pin Cont |
| FS150AR | 制造商:Hammond Power Solutions 功能描述:Transformer, Control, 1ph, 150VA, 600-12x24V, 60Hz |
| FS150K.5AB3 | 制造商:TE Connectivity 功能描述: |
| FS150R06KE3 | 功能描述:IGBT 模塊 IGBT MODULES 600V RoHS:否 制造商:Infineon Technologies 產品:IGBT Silicon Modules 配置:Dual 集電極—發射極最大電壓 VCEO:600 V 集電極—射極飽和電壓:1.95 V 在25 C的連續集電極電流:230 A 柵極—射極漏泄電流:400 nA 功率耗散:445 W 最大工作溫度:+ 125 C 封裝 / 箱體:34MM 封裝: |
發布緊急采購，3分鐘左右您將得到回復。