- 您現在的位置：買賣IC網 > PDF目錄44806 > FS1001-9RB2 (POWER-ONE INC) 1-OUTPUT 100 W DC-DC REG PWR SUPPLY MODULE PDF資料下載
參數資料
| 型號： | FS1001-9RB2 |
| 廠商： | POWER-ONE INC |
| 元件分類： | 電源模塊 |
| 英文描述： | 1-OUTPUT 100 W DC-DC REG PWR SUPPLY MODULE |
| 封裝： | METAL, CASE S02, MODULE |
| 文件頁數： | 4/33頁 |
| 文件大?。?/td> | 438K |
| 代理商： | FS1001-9RB2 |
第1頁第2頁第3頁當前第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁
S Series Data Sheet
100 Watt AC-DC and DC-DC Converters
APR 26, 2006 revised to SEP 25, 2006
Page 12 of 33
www.power-one.com
Fig. 15
Typical output response as a function of inhibit control
Table 5: Inhibit characteristics
Characteristic
Conditions
min
typ
max Unit
Vinh Inhibit Vo = on Vi min - Vi max –50
0.8
V
voltage
Vo = off
2.4
50
Iinh Inhibit current
Vinh = 0
–400
A
tr
Rise time
30
ms
tf
Fall time
depending on
Io
0
t
0
Inhibit
1
0.1
1
Vo/Vo nom
tr
tf
06001
Sense Lines
(Only single output models)
Important: Sense lines must always be connected! Incorrectly
connected sense lines may activate the overvoltage limitation,
resulting in a permanent short-circuit of the output.
This feature allows for compensation of voltage drops across the
connector contacts and if necessary, across the load lines. If the
sense lines are connected at the load rather than directly at the
connector, the user should ensure that the voltage differences
specified in the table below are not exceeded. We recommend
connecting the sense lines directly at the female connector.
To ensure correct operation, both sense lines (S+ and S–) should
be connected to their respective power outputs (Vo1+ and Vo1–)
and the voltage difference between any sense line and its
respective power output pin (as measured on the connector)
should not exceed the following values:
Table 6: Maximum voltage compensation allowed using
sense lines
Output
Total voltage difference
Voltage difference
voltage
between sense lines and
between
their respective outputs
Vo– and S–
5.1 V
< 0.5 V
< 0.25 V
12, 15, 24 V
< 1.0 V
< 0.25 V
If the output voltages are increased above Vo nom via the R-input
control, option P setting, remote sensing or option T, the output
currents must be reduced accordingly so that Po nom is not
exceeded.
Auxiliary Functions
i Inhibit for Remote On and Off
Note: With open i input the output is disabled.
The outputs may be enabled or disabled by means of a logic
signal (TTL, CMOS, etc.) applied between the inhibit input i and
the negative pin of output 1 (Vo1–). In systems with several
converters, this feature can be used to control the activation
sequence of the converters. If the inhibit function is not required,
connect the inhibit pin 18 to pin 14 to enable the outputs (active
low logic, fail safe).
Vi+
Vi–
Vo–
i
Vo+
Iinh
Vinh
06031
1.6
0.8
0
–0.8
–50
Vinh [V]
Iinh [mA]
–30
0
–10
10
30
50
2.0
1.2
0.4
–0.4
Vinh = 0.8 V
Vo = on
Vo = off
Vinh = 2.4 V
06032
Fig. 13
Definition of Vinh and Iinh.
Fig. 14
Typical inhibit current Iinh versus inhibit voltage Vinh
相關PDF資料 |
PDF描述 |
|---|---|
| FS1301-7RD7B2 | 1-OUTPUT 100 W DC-DC REG PWR SUPPLY MODULE |
| FS1501-7EPD4TB2 | 1-OUTPUT 100 W DC-DC REG PWR SUPPLY MODULE |
| FS1501-7EPD8B2 | 1-OUTPUT 100 W DC-DC REG PWR SUPPLY MODULE |
| FS1601-9EPD9B2 | 1-OUTPUT 100 W DC-DC REG PWR SUPPLY MODULE |
| FS2320-7EPD6B2 | 2-OUTPUT 100 W DC-DC REG PWR SUPPLY MODULE |
相關代理商/技術參數 |
參數描述 |
|---|---|
| FS1008 | 制造商:PREMO 制造商全稱:PREMO CORPORATION S.L 功能描述:Ferrite Chip Inductor 1008 High L |
| FS1008-103+ | 制造商:PREMO 制造商全稱:PREMO CORPORATION S.L 功能描述:Ferrite Chip Inductor 1008 High L |
| FS1008-122+ | 制造商:PREMO 制造商全稱:PREMO CORPORATION S.L 功能描述:Ferrite Chip Inductor 1008 High L |
| FS1008-152+ | 制造商:PREMO 制造商全稱:PREMO CORPORATION S.L 功能描述:Ferrite Chip Inductor 1008 High L |
| FS1008-182+ | 制造商:PREMO 制造商全稱:PREMO CORPORATION S.L 功能描述:Ferrite Chip Inductor 1008 High L |
發布緊急采購，3分鐘左右您將得到回復。