- 您現在的位置：買賣IC網 > PDF目錄382961 > FM25W256-S (Electronic Theatre Controls, Inc.) 256Kb FRAM Wide Voltage Serial Memory PDF資料下載
參數資料
| 型號： | FM25W256-S |
| 廠商： | Electronic Theatre Controls, Inc. |
| 英文描述： | 256Kb FRAM Wide Voltage Serial Memory |
| 中文描述： | 寬電壓的256Kb串行FRAM的記憶 |
| 文件頁數： | 6/13頁 |
| 文件大?。?/td> | 165K |
| 代理商： | FM25W256-S |
FM25W256
Rev. 1.0
Aug. 2004
Page 6 of 13
CS
SCK
SI
SO
Hi-Z
0 1 2 3 4 5 6 7
0 0 0 0
0 1 0 0
Figure 6. WRDI Bus Configuration
RDSR - Read Status Register
The RDSR command allows the bus master to verify
the contents of the Status register. Reading Status
provides information about the current state of the
write protection features. Following the RDSR op-
code, the FM25W256 will return one byte with the
contents of the Status register. The Status register is
described in detail in a later section.
WRSR – Write Status Register
The WRSR command allows the user to select
certain write protection features by writing a byte to
the Status register. Prior to issuing a WRSR
command, the /WP pin must be high or inactive.
Prior to sending the WRSR command, the user must
send a WREN command to enable writes. Note that
executing a WRSR command is a write operation
and therefore clears the Write Enable Latch.
Figure 7. RDSR Bus Configuration
Figure 8. WRSR Bus Configuration
Status Register & Write Protection
The write protection features of the FM25W256 are
multi-tiered. Taking the /WP pin to a logic low state
is the hardware write protect function. All write
operations are blocked when /WP is low. To write the
memory with /WP high, a WREN op-code must first
be issued. Assuming that writes are enabled using
WREN and by /WP, writes to memory are controlled
by the Status register. As described above, writes to
the status register are performed using the WRSR
command and subject to the /WP pin. The Status
register is organized as follows.
Table 2. Status Register
Bit
7
Name
WPEN
Bits 0 and 4-6 are fixed at 0 and cannot be modified.
Note that bit 0 (Ready in EEPROMs) is unnecessary
as the FRAM writes in real-time and is never busy.
The BP1 and BP0 control software write protection
features. They are nonvolatile! The WEL flag
indicates the state of the Write Enable Latch.
Attempting to directly write the WEL bit in the
status register has no effect on its state. This bit is
6
0
5
0
4
0
3
2
1
0
0
BP1
BP0
WEL
相關PDF資料 |
PDF描述 |
|---|---|
| FM30C256 | 12 AMP MINIATURE POWER RELAY |
| FM30C256-S | 256Kb Data Collector |
| FM361 | 2mm TERMINAL STRIP |
| FM362 | 2mm TERMINAL STRIP |
| FM3808 | 4Kb FRAM Serial 3V Memory |
相關代理商/技術參數 |
參數描述 |
|---|---|
| FM25W3S-K121 | 制造商:FCT Group 功能描述: |
| FM25W64-G | 功能描述:F-RAM SPI FRAM 64k 3-5V RoHS:否 存儲容量:512 Kbit 組織:64 K x 8 接口:SPI 工作電源電壓:2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube 制造商:Cypress Semiconductor |
| FM25W64-GTR | 功能描述:F-RAM SPI FRAM 64k 3-5V RoHS:否 存儲容量:512 Kbit 組織:64 K x 8 接口:SPI 工作電源電壓:2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube 制造商:Cypress Semiconductor |
| FM260 | 功能描述:肖特基二極管與整流器 SM Schot Bar Rect SMB,2A,60V. RoHS:否 制造商:Skyworks Solutions, Inc. 產品:Schottky Diodes 峰值反向電壓:2 V 正向連續電流:50 mA 最大浪涌電流: 配置:Crossover Quad 恢復時間: 正向電壓下降:370 mV 最大反向漏泄電流: 最大功率耗散:75 mW 工作溫度范圍:- 65 C to + 150 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-143 封裝:Reel |
| FM260A | 功能描述:肖特基二極管與整流器 SM Schot Bar Rect SMB,2A,60V. RoHS:否 制造商:Skyworks Solutions, Inc. 產品:Schottky Diodes 峰值反向電壓:2 V 正向連續電流:50 mA 最大浪涌電流: 配置:Crossover Quad 恢復時間: 正向電壓下降:370 mV 最大反向漏泄電流: 最大功率耗散:75 mW 工作溫度范圍:- 65 C to + 150 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-143 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。